Greatly reduces the rotating mass for that extra boost in 13.5T and 17.5T spec racing. The spool set weighs 18gr with the spur gear and the included coated steel outdrive cups. Machined 75T pom spur gear is included (replacement: Exotek 1545) and bolts on to the lightweight alloy spool. For non-boosted 13.5T and 17.5T classes only. Note: Must use anti wear grease for the...

The much stronger machined POM spur gear reduces the chances of stripped gears and includes the machined 7075 mounting plate with hardware. The 2 piece design also makes for quick and easy spur gear changes - you do not have to open the gear diff and remove the outdrive, or refill the oils etc. The alloy mounting plate also provides cooling of the diff fluid for more...

Extra heavy duty B suspension hanger block. Beefier shape insures protection from frontal arm impacts. Some pictures show the part in build condition, we'll only deliver the mentioned set.

The main weight is 40gr and included are 2 add on 8gr weights (16gr total add on plus the 40gr main weight) so that you can tune the rear weight of your buggy as needed. The weight set is also slightly angled off of the chassis to maintain chassis flex. Some pictures show the part in build condition, we'll only deliver the mentioned set.

By using longer screws (not included!) you can stack on up to 16gr additional weights as shown. Requires Exotek Weight Set 1807! Some pictures show the part in build condition, we'll only deliver the mentioned set.

Eliminates the flex around the center diff and eliminates the play at the bearing mount to prevent stripped spur gears with high powered motors. Some pictures show the part in build condition, we'll only deliver the mentioned set.

By adding mounting points to the 2 diff cover holes this will help prevent snapping the 2 upper bulkhead screws off of the bulkhead. To open the diff cover you will need to loosen the 6 camber place screws as well. Some pictures show the part in build condition, we'll only deliver the mentioned set.

Replacement 81 Spur Gear for Exotek 1798

Eliminates the problem of the rear hub hinge pins sliding out of the arms during impacts. Securely holds the hinge pins and hubs in the rear arm, thanks to the captured pin and lock nut design. Note: a 3mm drill bit or reamer is needed to open the front small hole of the arms for the pins to pass through. Some pictures show the part in build condition. The car is not part of...

Made of brass and black coated to reduce corrosion, this heavy hanger helps to add more rear traction. Can be combined with the Exotek 40gr weight set 20-1807. Some pictures show the part in build condition. The car is not part of the delivery content.

Made of hard steel, black coated to reduce corrosion and weighs 13gr, this heavy duty hanger lasts much longer than the alloy block and resists being worn away at the bottom due to abrasive track conditions. Some pictures show the part in build condition. The car is not part of the delivery content.

Reinforced design minimizes any extra cut outs to increase strength, yet only weighs 6gr. Some pictures show the part in build condition. The car is not part of the delivery content.

Reinforced alloy design elliminates the problem of the hex bearing posts stripping in the plastic cranks allowing for easier maintenance and disassembly. Includes steel bearing posts that doesn't mushroom when assembled which also makes for easier bearing removal. Gives your EB410 a smooth factory racing look thanks to the polished surfaces and our special glossy navy blue...

Crafted to greatly lower the looks and cg over the stock body the EDGE body sits 8mm lower than the stock body. It was also taken great care to still allow the mounting of the fan above the motor and still allow normal height or low profile servo use. Clean lines are used througout for a clean "aero" downforce package, yet allows easy custom painting thanks to the smooth and...

Eliminates the problem of not being able to push down on the posts when screwing them into the bulkheads with a socket driver. Lightweight, smooth fitting, heavy duty and a great addition to make maintenance on your EB410 a breeze! One picture shows the parts in build condition to show the usage. The car is not part of the delivery content.

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility: - Tekno RC EB48.4 - Tekno RC NB48.4 Some pictures show the part in build condition to show the usage.

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility: - Tekno RC EB48.4 - Tekno RC NB48.4 Some pictures show the part in build condition to show the usage.

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility: - Tekno RC EB48.4 - Tekno RC ET48.3 (use TKR8100 ackerman plate) - Tekno RC MT410 (use TKR8100 ackerman plate) - Tekno RC NB48.4 - Tekno RC NT48.3 (use TKR8100 ackerman plate) Some pictures show the part in build...

This 6.5mm wide hexes are +2mm (per hex) compared to the stock hexes, allowing you to tune the width of your buggy. Note - 6.5mm hexes can be used on the front and rear axles! Polished and anodized in a rich navy color. Including M2 hardware - don't over tighten!

This 7.5mm wide hexes are +3mm (per hex) compared to the stock hexes, allowing you to tune the width of your buggy. Note - 7.5mm hexes are only supposed to be used on the rear axles! Polished and anodized in a rich navy color. Including M2 hardware - don't over tighten!

The ball stud has been switched to an upright angle, yet still matches the stock geometry for easier roll center adjustments by adding washers (not included). The hubs are omnidirectional so that they can be mounted on either side. Extra durable for high powered applications and polished and anodized in Tekno colours.

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility; + Tekno RC EB48 2.0 + Tekno RC NB48 2.0

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility; + Tekno RC EB48 2.0 + Tekno RC NB48 2.0

Extra durable for high powered applications and polished and anodized in glossy Tekno team colors for that factory look. Matches the stock geometry. Compatibility; + Tekno RC EB48 2.0 + Tekno RC NB48 2.0

Heavy duty 7075 alloy top plate brace for the Tekno NB/NT/EB 48 line including 2.0 and 2.1.

New heavy duty alloy front steering spindle set for the EB410.2 AND ET410.2. Extra durable for high powered applications and polished and anodized in Tekno team colors as well as being machined a second time to insure precise bearing fit. COMPATIBLE WITH; EB410.2 ET410.2 EB410 ET410 Needed for the complete assembly: (4) M3x10 Button Head Screws And at least one of the...

Replacement 72t delrin machined spur gear for Exotek spur set 2174 and 1798.

Heavy duty 7075 machined alloy steering servo mount with carbon fiber electronics tray for the EB48 series. Lightweight yet high strength factory style servo mounting to reduce the risk of stripped plastics. Polished and anodized 7075 with woven carbon fiber plate. Fits Tekno RC EB48 2.0, 2.1 and ET48 2.0.

Polished and anodized in factory colors. The alloy construction maintains proper gear mesh for longer gear life and reduces the chance of stripped screws coming loose in a race. Uses the stock hardware. Always use blue thread lock and do not over tighten screws.

Replacement 68t delrin machined spur gear for Exotek spur set 2174 and 1798. Engraved with 68 on the side. Smaller than stock for use in stock spec type classes.