The Tunalyzer is the latest tool that Hobbywing recommends to any RC hobbyist who wants to achieve optimal results when selecting and maintaining motors. Achieve meaningful and accurate results with 12 preset test parameters. The measurement is supported, among other things, by the built-in voltage regulator, which ensures that comparable results are always obtained under...

Replacement for the stock XR8 capacitor.

Upgrade your G2 ESC with this capacitor module. It has non polarity - so you will not damage your capacitor when confusing red and black :-)

Upgrade your G2 ESC with this capacitor module. It has non polarity - so you will not damage your capacitor when confusing red and black :-)

Replacement for the stock XR10 Stock Spec and 160A G2 switch.

Upgrade your G2 ESC with this alu frame and the included 30x30x10mm tuning fan.

Upgrade your G2 ESC with this alu frame and the included 30x30x10mm tuning fan.

Standard fan - as replacement part for the G2S ESC.

Standard fan - as replacement part for the G2S ESC.

Sensor Wire for Brushless Motors

Programing Box 2C LED for XERUN, EZRUN and QUICRUN

Overview This multifunction program box is for programming HOBBYWING brushless ESCs. Its friendly LCD interface makes ESC programming easy and quick. With a PC, you can upgrade ESC firmware and further adjust ESC parameters online. Besides, it’s compact, portable and very applicable for field use. Thanks to built-in OTA programming feature through Bluetooth™, you can now use...

Suitable for: XERUN & EZRUN (car) PLATINUM (air) SEAKING PRO (boat) This Bluetooth modul requieres a smartphone / tablet with iOS or Android. HobbyWing offers a free app for those two operating systems.

Hobbywing 3060100 - DC-Booster for 1s Lipo, Output 6V 2 Ampere 1S DC-DC BOOSTER is a DC-DC power booster module which can draw power from the 1S Lipo battery then boosts it to the voltage (6V) suits the receiver & servo and provides the continuous output current up to 3Amp. 1S DC-DC BOOSTER is mainly applied in 1/12th scale RC vehicles. The 1/12th scale car usually uses 1S...

Nice tool whichs helps to replace a rotor within a few moments. Will fit to 1/10 motors, type 540. Maximum rotor diameter is 13.0mm. Not only for HobbyWing motors!

Silicon Wire - super soft - 11AWG - 100cm - BLACK

Silicon Wire - super soft - 13AWG - 100cm - BLACK

Sensor converter cable with JST connector, suitable for sensored brushless motors (z.B. Ezrun MAX8 G2, MAX4 HV). This cable is characterized by its particularly high water protection (according to the IP67 standard). Note: No thermal motor protection.

XERUN V10 G4 - Rotor 12.5mm - F7 - 24.1mm length

Includes front and rear endbell, bearings, sensor unit and screws.

XERUN Bandit G4 - Rotor 13.9mm - D5 - 24.1mm length

Standard rotor for the Hobbywing G4R motors with 13.5T or 17.5T.

XERUN Bandit G4 - Rotor 13.3mm - D5 - 24.1mm length

Optional rotor for the Hobbywing G4R motors with 13.5-17.5T.

Optional rotor for the Hobbywing G4R motors.

Length: 115mm Weight: 3g

Replacement Power Switch for Xerun Justock XR10 G3S

Special designed spare part for special HobbyWing ESC.

Messurements: Size: 35x35x10mm Distanz Hole-to-Hole: ca. 30mm including 4 screws

Specification: Ball Bearing Wire length ca. 20mm 10.000RPM@5V 0.13A

Messurements: Size: 20x20x8mm including 2 screws

Super Capacitor Modul Specification Capacity: 330uF*2. Voltage: 16V. Impedance: 0.002 ohm Ripple Current Endurance: 24 Amp Size: 29mm * 13mm * 13.2mm Weight: 5g Suitable ESC: XERUN and EZRUN series 1/10 scale ESC. Features Super low impedance Low temperature in working state Reduces the RF interference to make the RC model more reliable Improves the burst power when the...

Fits most 540 1/10 brushless motors

Increases the motor shaft diameter from 3.17mm to 5mm for bigger pinions.

Specification: Oil/Porous Bearing No Plug Wire length 40mm 13.000RPM@12V 0.09A

Specification: Ball Bearing Wire length ca. 20mm 14.000RPM@12V 0.13A

Messurements: Size: 25x25x10mm Distanz Hole-to-Hole: ca. 20mm including 4 screws

Specification: Ball Bearing Wire length ca. 50mm 10.000RPM@5V

Specification: Ball Bearing Wire length ca. 40mm 10.000RPM@5V

Specification: Ball Bearing Measurements: 25x25x7mm 5V incl. two plug options

Specification: Ball Bearing Measurements: 25x25x7mm 5V incl. two plug options

Specification: Ball Bearing Wire length ca. 20mm Measurements: 50x50x10mm