ALU NUT FOR 1/8 OFF-ROD SYSTEM (4)

Allows for quick and easy camber checks for the most frequently-used wheel camber angles: 1, 2 and 3°.

Special tool to adjust the camber at RX8 version with a hole in the upper suspension arm / turnbuckle. 2.0mm diameter - may also fit for other cars with same diameter.

• chassis droop gauge support blocks for 1/8 and 1/10 cars • 2 pcs in a set • allows adjustment of front/rear droop when used with #107711 Chassis Droop Gauge for 1/8 on road and with #107720 Chassis Droop Gauge for 1/10 off-road

• chassis droop gauge support blocks for 1/10 cars • 2 pcs in a set • allows adjustment of front/rear droop when used with #107712 Chassis Droop Gauge for 1/10

Place the front support block below the servo saver, and place the rear support block below the rear suspension mounting. Using the #107717 Chassis Ride Height & Droop Gauge 0 to -13 mm for 1/8 Off-Road with elevated scales, measure the droop under the wheel axle hex. Replacement for HUDY 107703

• chassis droop gauge for 1/8 and 1/10 cars • allows adjustment of the front/rear droop when used with #107701 Chassis Support Blocks for 1/8, 1/10

• chassis droop gauge for 1/10 cars • allows adjustment of the front/rear droop when used with #107702 Chassis Support Blocks for 1/10

CHASSIS RIDE HEIGHT GAUGE 2 MM TO 15 MM (1 MM STEPPED)

ULTRA-FINE CHASSIS DROOP GAUGE 4.0-6.6MM must be used with #107702 Chassis Support Blocks for 1/10

CHASSIS RIDE HEIGHT GAUGE 0 MM TO 15 MM (BEVELED)

ULTRA-FINE CHASSIS RIDE HEIGHT GAUGE 3.8-8.0mm - 0.2mm increments

• allows adjustment of front/rear droop (downstop) when used with #107704 HUDY Chassis Droop Gauge Support Blocks for Off-road Cars • droop range (0-13mm)

Stepped surfaces in the 2.6-5.6mm range have 0.2mm increments for fine adjustment.

One-piece highly-accurate tool for quick downstop checking has an integrated support block that supports the chassis while the stepped scale indicates the downstop setting. Includes a downstop range of 1.0-6.5mm.

CHASSIS RIDE HEIGHT GAUGE 17MM TO 30MM FOR 1/8 & 1/10 OFF-ROAD

CHASSIS RIDE HEIGHT GAUGE for Offroad

CHASSIS RIDE HEIGHT GAUGE for Offroad

CHASSIS RIDE HEIGHT GAUGE for Offroad

Allows you to perform quick & easy camber checks for 3 most frequently-used wheel camber angles: 1.5°, 2.0°, and 2.5°.

Adjustable from -5° to +10° Suitable for 1:12, 1:10 and 1:8 onroad.

Adjustable from -5° to +10° Suitable for 1:12, 1:10 and 1:8 onroad. 1:10 and 1:8 offroad (up tp 110mm tire diameter)

CHASSIS RIDE HEIGHT GAUGE for Offroad

Professional fully-adjustable droop gauge to check the droop of the suspension downtravel in range 80~140mm. Great for quick and instant droop check directly on ready-to-race car with no other set-up equipment needed. This is the more professional version to the traditional droop gauge featuring an adjustable slider. The gauge is inserted on the nut that holds the shock on...

• For 1/8 and 1/10 off-road cars • Quick and instant droop check • 70~140mm range • Use on ready-to-race car • Wear resistant • Precise laser engraved scale • CNC-machined from aluminum • Black coated . Professional droop gauge to check the drop of the suspension downtravel in range 70~140mm. Great for quick and instant droop check directly on ready-to-race car with no other...

CHASSIS BALANCING SIMPLE TOOL (2 PCS.)

HUDY QUICK-TWEAK STATION + ALU CARRY CASE Having the proper tweak is one of the most important factors that influences a car’s overall performance; a badly-tweaked car has a very negative impact on a car's handling. Checking and correcting tweak is very important; pro racers check for tweak a number of times after each run. The HUDY Quick-Tweak Station allows you to quickly...

HUDY QUICK-TWEAK STATION + ALU CARRY CASE

HUDY Tweak Board is a very handy and useful tool for making sure that the chassis and top deck are completely straight after tightening down the top deck screws. The tweak board is used by all the professional drivers between runs to achieve a perfectly straight car without any unwanted mechanical tweak. To remove unwanted tweak takes only a seconds using HUDY Tweak Board...

Replacement for Quick Tweak Station 107904

Standard spare part for #107903 and #107904 Quick Tweak Stations.

Alu Setup System - for measuring camber, caster and toe. There are different versions available: 108001 - 1:8 Onroad Suitable for cars like XRAY RX8. Does not fit for 1:8 GT (like XRAY GTX8). 108801 - 1:8 Offroad Sutiable for cars like XRAY XB8. XT8 will need a different toe gauge cause of the wider car. 108901 - 1:10 Offroad Suitable for cars like XRAY XB2, XT2, XB4, XT4 or...

Set Up Alu TRIANGLE

Set Up Alu TRIANGLE for Setup System HUDY 109301

Upside Measure Platte 1:8 Onroad for Setup System 108005 / 108001

Complete Set of Setup Tools + Carrying Bag - For 1/8 Onroad Car This set includes: 107701 - Chassis Droop Gauge Support Blocks 20mm for 1/8 - LW(2) 107711 - Chassis Droop Gauge -3 to 10 mm for 1/8, 1/10 107716 - Ultra-Fine Chassis Ride Height Gauge 3.8-8.0mm 107880 - Chassis Balancing Tool (2) 107903 - Tweak Station for 1/8 & 1/10 On-road Cars (without Alu Carry Case) 108005...

ALU NUT FOR SET-UP TRIANGLE (4)

CNC-machined premium-quality aluminum set-up wheels for 1/8 on-road cars allow for perfectly precise and repeatable set-up adjustment and tweak correction. Eliminates set-up errors inherent in using standard on-road tires. Precision-machined to exacting tolerances, each alu set-up wheel in a set is perfectly matched. Suspension set-up, ride height setting and checking tweak...

160x98mm size - with different fields for small parts. Including holes for soldering 4mm and 5mm plugs. Including a tool for measuring the length of M3 screws. Including two 10mm holes for your gear diff.

215x50mm size - with different fields for small parts. Take care: Will be delivered without content.

215x100mm size - with different fields for small parts. Take care: Will be delivered without content.

The tray includes a magnetic anti-slip mat, which can be glued on the underside of the tray.

Size: 570x450mm Thickness: 10mm Weight: 1970g Suitable for: 1/8 offroad (also truggy!) Suitable measuring sticker: 108213 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

PLASTIC SET-UP BOARD DECAL Size: 420x330mm Suitable for: 1/8 onroad (no GT!) For HUDY board: 108200

PLASTIC SET-UP BOARD DECAL Size: 562x449mm Suitable for: 1/8 offroad (also truggy) For HUDY board: 108202

Size: 390x290mm Thickness: 10mm Weight: 860g Suitable for: 1/10 onroad + 1/12 Suitable measuring sticker: 108360 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x290mm Thickness: 10mm Weight: 860g Suitable for: 1/10 onroad + 1/12 Suitable measuring sticker: 108360 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x290mm Thickness: 10mm Weight: 860g Suitable for: 1/10 onroad + 1/12 Suitable measuring sticker: 108360 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x290mm Thickness: 10mm Weight: 860g Suitable for: 1/10 onroad + 1/12 Suitable measuring sticker: 108360 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 550x340mm Thickness: 10mm Weight: 1420g Suitable for: 1/8 onroad (no GT!) Suitable measuring sticker: 108560 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved. Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all...

Size: 550x340mm Thickness: 10mm Weight: 1420g Suitable for: 1/8 onroad (no GT!) Suitable measuring sticker: 108560 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 550x340mm Thickness: 10mm Weight: 1420g Suitable for: 1/8 onroad (no GT!) Suitable measuring sticker: 108560 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved

Size: 550x340mm Thickness: 10mm Weight: 1420g Suitable for: 1/8 onroad (no GT!) Suitable measuring sticker: 108560 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 550x340mm Thickness: 10mm Weight: 1420g Suitable for: 1/8 onroad (no GT!) Suitable measuring sticker: 108560 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

PLASTIC SET-UP BOARD DECAL Size: 545x331mm Suitable for: 1/8 onroad For HUDY board: 1085 01 / 108502 / 108503 / 108504 / 108505

Size: 390x335mm Thickness: 10mm Weight: 980g Suitable for: 1/10 offroad buggy Suitable measuring sticker: 108660 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x335mm Thickness: 10mm Weight: 980g Suitable for: 1/10 offroad buggy Suitable measuring sticker: 108660 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x335mm Thickness: 10mm Weight: 980g Suitable for: 1/10 offroad buggy Suitable measuring sticker: 108660 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x335mm Thickness: 10mm Weight: 980g Suitable for: 1/10 offroad buggy Suitable measuring sticker: 108660 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.

Size: 390x335mm Thickness: 10mm Weight: 980g Suitable for: 1/10 offroad buggy Suitable measuring sticker: 108660 Please note: It’s impossible to get a 100% flat board made of this kind of wood. HUDY will inspect all boards before shipment – so they are Q.C. approved.