Total length: 100mm Shaft diameter: 3.0mm Please be very careful! 1.5mm ball head is very fragil. If you are doing it wrong you will destroy screw and tool. No power tool! Just very low torque!

No problems with already painted bodies anymore :-) Colour is black. The red pictures are just to show how it will be used. Please note! The magnets are made from neodymium which makes them extremly magnetic. This is necessary for the little magnets so they can hold a body in position. A second feature of neodymium is, it is extremly brittle. The magnets are very strong and...

145mm total length.

Suitable for any popular tire truer like HUDY, Fastrax, HARD, Yokomo...

Super short nut socket driver.

Super short nut socket driver.

Spare part for TT-042 tool set.

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 20mm gap between the bulkheads. For example: Mugen MTC-1 Infinity IF14 ...and many more. Check your gap!

Suitable for 1/10 on-road/off-road, 1/8 on-road/GT/off-road. Description: After fold in smaller size,easy to pack. Bottom with carbon fiber balance plate, turn out the balance plate can increase holder stability. Each holder with 2 different size holes. Each size holes with 4 spacers, using which spacers depend on the shocks. Each holes with laser mark, easy to identify the...

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 18mm or 19mm gap between the bulkheads.

This Universal Cleaning Case helps to remove dust and dirt of the bearings/screws/small parts with hassle-free. Simply put the bearings/screws/small parts inside the cleaning case, add cleaners and shake the case until dust/dirt is being removed. Feature: For: Miscellaneous Specification: Length: approx. 60mm Width: approx. 31mm

Turnbuckle Duo- purpose Adjustment Tool T-Work's has a new product to aid in adjusting your Turnbuckles. The tool has a 2mm extended bit to allow easier adjusting for turnbuckles with hole. In addition, it comes with a 4mm turnbuckle tool on the other end.

Turnbuckle Duo- purpose Adjustment Tool T-Work's has a new product to aid in adjusting your Turnbuckles. The tool has a 1.6mm extended bit to allow easier adjusting for turnbuckles with hole. In addition, it comes with a 4mm turnbuckle tool on the other end.

T-Work's is pleased to introduce the Glow Plug Magnifier tool. The tool allows you to check the inner coil condition of the glow plug at 50x magnification; giving you a good gauge when it's time for replacement. The tool comes in T-Work's carbon-fibre design carry case. The button batteries are NOT included! 3 pcs AG10 needed.

L-Type hex wrench.

L-Type hex wrench.

L-Type hex wrench.

5.5mm - L-Type socket driver.

Build your MTC2 save and easy! Made for A2147B (nut, 8mm)

Build your MTC2 save and easy! Made for A2147A (ball joint, 9mm)

For bearings with 2-15mm inner diameter. Including 1/8 and 1/4 bearings.

Suitable for 1/10 (12mm hex) and 1/8 (17mm hex) wheels.

The length of this product is 50mm, which is suitable for the transmission shaft with a length of more than 50mm.

The length of this product is 31.5mm, which is suitable for the transmission shaft with a length of more than 31.5mm.

Made for offroad clutch - 1/8.

Made for onroad clutch - 1/8 and 1/10.

One driver - two sizes!

Useable for holes from 2-13mm.

Big Brush: Length: 205 mm Width: 50.8mm (2") Middle Brush: Length: 200mm Width: 38.1mm (1,5") Small Brush: Length: 195 mm Width: 25.4mm (1")

Big Brush: Length: 205 mm Width: 50.8mm (2")

Middle Brush: Length: 200mm Width: 38.1mm (1,5")

Small Brush: Length: 195 mm Width: 25.4mm (1")

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

Handle + 4x powertool insert

Suitable for 1/4 inch (6.35mm) bits.

5mm hex, 8mm nut and 10mm nut - all in one tool.

L-Type hex wrench. Take care: It's very small - only 90mm total length.

Handle + 4x insert

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

Powertool insert - 1/4 inches, 6.35mm

T-Work's Multi-Purpose Wrench Includes: - Handle - 8mm/10mm Nut Driver - 7075-T6 Hard Coated 17mm nut driver - 7075-T6 Hard Coated 17mm extra long nut driver

The small one!

Short version - for truggy wheels. Will also work for buggies.

Made for Mugen MBX8R.

Short version - for buggy wheels.

Made for 1/8 and 1/10.

Build your turnbuckles save and easy!

Build your turnbuckles save and easy!

Build your MTC2 save and easy!

Suitable for a range from +3 to -10 degrees camber. Suitable for 1:8 GT / Buggy and also 1:10 Offroad / Onroad. The inner graphite part is removeable to work also with a longer wheel axle (like 1:10 Offroad)

Suitable for 1/10 on-road - regular touring car shocks and also Awesomatix shocks. Can also used in combination with a vacuum pump (not included!) 14mm diameter for the standard shocks special shape for Awesomatix shocks on the other side 57mm total diameter (important for Tamiya Air Remover)

Suitable for HobbyWing XERUN V10 G3, G3R and G4 Motor versions.

Suitable for 1/10 (12mm hex) and 1/8 (17mm hex) wheels.

Make tire gluing great again!

Make tire gluing great again!