30xxxx - X4 / T4 / T3 / T2 / T1

XRAY 305934 - NARROW PINION GEAR ALU HARD COATED 34T 48dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 18T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 19T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 20T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 21T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 22T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 23T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 24T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 25T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 27T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 34T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

NARROW PINION GEAR ALU HARD COATED 35T 64dp Suitable for 1/10 (1/12, etc.) cars with 3.17mm shaft diameter.

Composite Hub for Battery Holder (2)

GRAPHITE BATTERY STRAP FOR LIPO/NIMH (SET)

LONG COMPOSITE LIPO BATTERY BACKSTOP (1+1)

T4 2014 Replacement Graphite Battery Plates for Adjustable Battery Holder Requires XRAY 306191 - T4 2014 Graphite + Alu Fully Adjustable Battery Holder for use. These are only replacement plates for the adjustable battery holder.

Requires XRAY 306191 - T4 2014 Graphite + Alu Fully Adjustable Battery Holder for use. These are only replacement parts for the adjustable battery holder.

Requires XRAY 306191 - T4 2014 Graphite + Alu Fully Adjustable Battery Holder for use. These are only replacement parts for the adjustable battery holder.

Will add ca. +7g to the total weight. Suitable for any XRAY T4! Genuine XRAY parts. Original is always best!

Genuine XRAY parts. Original is always best! Will be used instead of the graphite part 306530. Weight difference compared to 306530: + ca. 4.4 gr

Fully adjustable aluminum battery holder allows to move the batteries in all directions - front/rear and also left/right. The adjustable battery holder allows for easy and comfortable weight transfer adjustment. The front/rear weight balance can be adjusted in 4mm range. The battery holders allow to mount the battery tape over the top of the battery only without the...

Fully adjustable brass battery holder allows to move the batteries in all directions - front/rear and also left/right. The adjustable battery holder allows for easy and comfortable weight transfer adjustment. The front/rear weight balance can be adjusted in 4mm range. The brass material adds extra 7.5g weight for additional weight balance adjustment of the battery side of...

CNC-machined battery backstop for the adjustable battery holder for positioning batteries fore-aft/left-right. Designed for the slim battery pack. Quick & easy weight transfer adjustment. Made from 3.0mm premium-grade graphite material. TAKE CARE: It's not a complete battery mount. It's just an upgrade for the existing mount.

T4 2015 Alu Servo Mount - BLACK (2)

T4 2015 Alu Servo Mount - BLACK (2)

Optional floating forward mount servo holder set allows mounting of the servo holder to the chassis more forward which leads to increased steering and steering response. Recommended for conditions where better steering response is needes. Makes the car more reactive but less stable. Needs to be combined with the graphite part 306235.

The all-new, unique floating servo holder set includes graphite holder and aluminum bushings. The floating steering system is disconnected from the chassis and works fully independently without affecting flex. This makes the car easier to drive in high-traction conditions, and chassis roll is reduced especially driving through the curbs. The car also handles better on bumpy...

Optional floating forward mount servo holder set allows mounting of the servo holder to the chassis more forward which leads to increased steering and steering response. Recommended for conditions where better steering response is needes. Makes the car more reactive but less stable. Needs to be combined with the alu part 306205.

Genuine XRAY spares!

T4 2014 Alu Top Deck Mount - Orange Take care: XRAY says that it's also possible to use this part at the XRAY T4 2018. Without modifications this is NOT possible. You need to reduce the diameter of the post by grinding it.

XRAY PURE TUNGSTEN CHASSIS WEIGHT 10g Machined 10g pure tungsten chassis weight. The weights are smaller than the brass weights and are easier to install with a cleaner layout. The super small weights result in lower CG comparing to standard weights. Produced from very rare and heavy pure tungsten material, not a typical tungsten mixture. The pure tungsten has the highest...

T4 2014 Inner Pivot Pins (2)

Titan Suspension Pivot Pin (2)

Titan Suspension Pivot Pin (2)

Titan Suspension Pivot Pin (2)

Genuine XRAY parts. Original is always best! To be used with PSS inserts (308029) in PSS XLP shocks (like X4 2023).

Pistons which will fit only when used with PSS system 308039!

Genuine XRAY parts. Original is always best! TAKE CARE! There is a mistake in the manual of T4 2020. Also the correction of the PDF manual might be still complicated. 308029 = ULP = kit shocks 308308 - ULTRA low profile => SHORT 308039 = SLP = optional shocks 308307 - SUPER low profile => LONG

ALU XRAY SHOCK SPRING RETAINING COLLAR (4)

ALU XRAY SHOCK SPRING RETAINING COLLAR - ORANGE (4)

Looks pretty cool. No further benefits ;-)

COMPOSITE NON-ADJUSTABLE PISTONS FOR ALU T2'008 SHOCK ABSORBERS - V3

T4 COMPOSITE PISTONS 4-HOLE 1.0-1.2MM, 3-HOLE 1.0-1.2MM

Spare pistons which will fit only when used with PSS system 308039!

T4 Alu Progressive Shock System - Set (2) - PSS Will fit to each kind of T4. Dampers 308307-O are necessary. No complete dampers, only optionals to upgrade your existing dampers! Innovative progressive shock system for touring cars for improved traction and steering characteristics. Shock insert has 3 triangle cuts and is used with piston without holes. The hardness of the...

T4 ALU SHOCK ADJUSTABLE NUT - BLACK

T4 ALU SHOCK ADJUSTABLE NUT - ORANGE

Genuine XRAY parts for your T4!

SHOCK ABSORBER MEMBRANE (4)

SHOCK ABSORBER MEMBRANE - LOW (4)

T4 SHOCK ABSORBER MEMBRANE (4)

SHOCK FOAM INSERTS (4)

SHOCK FOAM INSERTS - LOW (4)

T4 SHOCK FOAM INSERT (4)

Genuine XRAY spares!

Can be used only with XLP shocks! It's possible to upgrade the X4 (first generation) when using it with XLP shocks. Diameter: 14mm Length: 17mm (which is REALLY short!)

Can be used only with XLP shocks! It's possible to upgrade the X4 (first generation) when using it with XLP shocks. Diameter: 14mm Length: 17mm (which is REALLY short!)

Can be used only with XLP shocks! It's possible to upgrade the X4 (first generation) when using it with XLP shocks. Diameter: 14mm Length: 17mm (which is REALLY short!)

Can be used only with XLP shocks! It's possible to upgrade the X4 (first generation) when using it with XLP shocks. Diameter: 14mm Length: 17mm (which is REALLY short!)