COMPOSITE C-HUB RIGHT - 6° DEG. - HARD

Carbon Chassis 2.2mm

Carbon Top Deck 2.2mm

Graphite Bumper Plate

Foam Bumper

REAR BODY MOUNT SET +1MM HEIGHT

REAR BODY MOUNT SET +2MM HEIGHT

Genuine XRAY parts for your T4!

Genuine XRAY parts for your T4!

Very handy, easily externally adjustable body post from Swiss 7075 T6 aluminum. Allows for adjustment of body height by 3mm without needing to change the position on the body post. Fits T2, T3, T4, X4 cars (front & rear) and NT1 cars (front only).

T4 2014 Alu Adjustable Body Post Stop (2)

Original XRAY spare and option parts!

Alu Upper Clamp (L+R) - Orange

These beautiful 7075 T6 aluminum adjustable ball-bearing hubs are direct replacement of the standard composite ones included in the kit. The aluminum hubs reduce the friction and make the car to run more free with increased the drivetrain efficiency. Suggested especially for stock class where super low friction drive train is important. The aluminum hubs are stronger and...

Graphite Shock Tower Rear 3.0mm

T4 2014 Front Suspension Arm - Graphite

The aluminum suspension arm is a direct replacement for the standard composite graphite arm. The aluminum arm works well on high traction or permanent carpet tracks as it makes the car easier to drive with less stopping and better cornering speed. The arms are available for front and rear and are available either individually or as a set. Features a single optimized shock...

Alu steering blocks with ultra-strong construction provides very long life and durability in even the most extreme racing conditions. Composite bushings are used to secure the ball-bearings in both sides of this steering block; this allows the ball-bearings to fit perfectly and turn freely, giving much higher lifetime compared to bearings installed directly into aluminum...

GRAPHITE EXTENSION PLATE FOR ALU STEERING BLOCK (2) The graphite extension for alu steering block made from premium-grade graphite material. Allow for easy Ackermann position adjustment for fine-tuning on all surfaces and track conditions.

COMPOSITE STEERING BLOCK - MEDIUM - V2

COMPOSITE STEERING BLOCK - GRAPHITE Suitable for any kind of T2, T3 or T4.

Works as spare part for 302202.

ALU C-HUB FRONT BLOCK - 0° DEG.

ALU C-HUB FRONT BLOCK, RIGHT - 2° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 2° DEG - ORANGE

ALU C-HUB FRONT BLOCK, RIGHT - 4° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 4° DEG - ORANGE

ALU C-HUB FRONT BLOCK, RIGHT - 6° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 6° DEG. - ORANGE

COMPOSITE C-HUB RIGHT - 2° DEG. - MEDIUM

COMPOSITE C-HUB LEFT - 2° DEG. - MEDIUM

COMPOSITE C-HUB RIGHT - 6° DEG. - MEDIUM - ECS

COMPOSITE C-HUB LEFT - 6° DEG. - MEDIUM

COMPOSITE C-HUB RIGHT - 2° DEG. - HARD

COMPOSITE C-HUB LEFT - 2° DEG. - HARD

COMPOSITE C-HUB LEFT - 6° DEG. - HARD

Composite C-Hub right 4° graphite (ECS)

Composite C-Hub left 4° graphite (ECS)

Anti-Roll Bar Front 1.3mm

Anti-Roll Bar Front 1.4mm

ALU DUAL SERVO SAVER ARM + BALL-BEARINGS (2) More precision, more steering angle.

Genuine XRAY parts for your T4!

The 8mm steering plate was developed to improve the cornering speed. This steering plate has less steering response and is recommended for large asphalt tracks with long sweepers to improve cornering speed or very technical carpet tracks to eliminate oversteering in the chicanes. The bearings are factory pressed into the steering plate which eliminates play in the assembly....

T4 2014 Graphite Steering Plate Set

Those screws are recommened to reduce the play in the T4 alu steering. How to use? Check the video of Alexander Hagberg: https://www.facebook.com/alexander.hagberg/videos/957117651161275/

ADJ. TURNBUCKLE L/R 40 MM - HUDY SPRING STEEL (2)

ALU ADJ. TURNBUCKLE M3 L/R 39 MM - ORANGE - SWISS 7075 T6 (2 pieces)

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Will lower the suspension mount by 0.5mm - as replacement for the standard mount 302710. Searching for the other side? 302712-O :-) Will fit to any T4 starting with the 2014!

• 3x heavier than alu holders • Eliminates need for additional chassis weights • Eliminates negative chassis flex • Equal weight addition left & right • Available for front or rear suspension Brass suspension holders were created to add additional weight to the car to attain the minimum weight limit, and to replace other chassis-mounted weights which negatively influence...

Will lower the suspension mount by 0.5mm - as replacement for the standard mount 302720. Searching for the other side? 302722-O :-) Will fit to any T4 starting with 2014!

Alu Lower Adjustment Bulkhead Front Right - Orange

Alu Lower Adjustment Bulkhead Front Left - Orange

Alu Motor Mount Bulkhead - orange

Graphite Shock Tower Rear 3.0mm

T4 2014 Rear Suspension Arm - Graphite

The aluminum suspension arm is a direct replacement for the standard composite graphite arm. The aluminum arm works well on high traction or permanent carpet tracks as it makes the car easier to drive with less stopping and better cornering speed. The arms are available for front and rear and are available either individually or as a set. Features a single optimized shock...

REAR TURNBUCKLE L/R 26 MM - HUDY SPRING STEEL (2)

ALU ADJ. TURNBUCKLE L/R 26 MM - ORANGE - SWISS 7075 T6 (2 pieces)

COMPOSITE UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - MEDIUM