COMPOSITE C-HUB RIGHT - 6° DEG. - HARD

T3'12 CHASSIS 2.5MM GRAPHITE We‘ve opened your car kit / your packaging and checked the lower deck, to guarantee a consistent quality . That way we make sure that you‘ll only receive a 100% proper product. RC-KleinKram - You race, we care!

ALU COUNTERSUNK SHIM - ORANGE (4)

T3'12 UPPER DECK 2.0MM GRAPHITE

IMPACT ABSORBING FRONT BUMPER

Optional upper bumper brace for T4 reinforces the front bumper assembly and eliminates the chassis breaking in serious crashes. CNC-machined from 3.5mm thick premium-grade graphite material.

FRONT BODY MOUNT SET 6MM Do you need the bumper posts as well? Partnumber 301321 for the low bumper (T4, T4 2014) or 301325 for the high bumper (all T2 and T3)

FRONT BODY MOUNT SET 6MM Perfect for the rear horizontal mount. Not recommended to be used in front.

FRONT BODY MOUNT SET +1MM HEIGHT Do you need the bumper posts as well? Partnumber 301321 for the low bumper (T4, T4 2014) or 301325 for the high bumper (all T2 and T3)

T4 COMPOSITE BRACE FOR BUMPER - LOW (2)

REAR BODY MOUNT SET 6MM

REAR BODY MOUNT SET +1MM HEIGHT

Very handy, easily externally adjustable body post from Swiss 7075 T6 aluminum. Allows for adjustment of body height by 3mm without needing to change the position on the body post. Fits T2, T3, T4, X4 cars (front & rear) and NT1 cars (front only).

T4 2014 Alu Adjustable Body Post Stop (2)

T3 ALU UPPER CLAMP WITH ADJ. ROLL-CENTER (L+R) - ORANGE

ALU NUT FOR SUSP. HOLDER (2 pieces)

SHOCK TOWER FRONT - GRAPHITE 3.0MM

FRONT SUSPENSION ARM - HARD - 2-HOLE

FRONT SUSPENSION ARM - EXTRA-HARD - 2-HOLE

T4 2014 Front Suspension Arm - hard

T4 2014 Front Suspension Arm - Graphite

T4 2014 Graphite Arm Stiffener Front (2) Important note : The carbon plates are fastened with screws M2.5 with 1.5mm allen head. Therefore it is extremely important to use a hex screwdriver is in a state of 100 %. A hexagon with wear will destroy the screws . It is also necessary to go with caution to the screws . Not tighten too fast , do not fix sloping ! In order to be...

Alu steering blocks with ultra-strong construction provides very long life and durability in even the most extreme racing conditions. Composite bushings are used to secure the ball-bearings in both sides of this steering block; this allows the ball-bearings to fit perfectly and turn freely, giving much higher lifetime compared to bearings installed directly into aluminum...

GRAPHITE EXTENSION PLATE FOR ALU STEERING BLOCK (2) The graphite extension for alu steering block made from premium-grade graphite material. Allow for easy Ackermann position adjustment for fine-tuning on all surfaces and track conditions.

COMPOSITE STEERING BLOCK - HARD - V2

COMPOSITE STEERING BLOCK - GRAPHITE Suitable for any kind of T2, T3 or T4.

Works as spare part for 302202.

BALL-BEARING COMPOSITE BUSHING (4)

COMPOSITE C-HUB BUSHING (2+2)

ALU C-HUB FRONT BLOCK - 0° DEG.

ALU C-HUB FRONT BLOCK, RIGHT - 2° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 2° DEG - ORANGE

ALU C-HUB FRONT BLOCK, RIGHT - 4° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 4° DEG - ORANGE

ALU C-HUB FRONT BLOCK, RIGHT - 6° DEG. - ORANGE

ALU C-HUB FRONT BLOCK, LEFT - 6° DEG. - ORANGE

Composite C-Hub right 0° Medium (ECS)

Composite C-Hub left 0° Medium (ECS)

COMPOSITE C-HUB RIGHT - 2° DEG. - MEDIUM

COMPOSITE C-HUB LEFT - 2° DEG. - MEDIUM

COMPOSITE C-HUB RIGHT - 6° DEG. - MEDIUM - ECS

COMPOSITE C-HUB LEFT - 6° DEG. - MEDIUM

Composite C-Hub right 0° hard (ECS)

Composite C-Hub left 0° hard (ECS)

COMPOSITE C-HUB RIGHT - 2° DEG. - HARD

COMPOSITE C-HUB LEFT - 2° DEG. - HARD

COMPOSITE C-HUB LEFT - 6° DEG. - HARD

Composite right 0° graphite (ECS)

Composite C-Hub left 0° graphite (ECS)

Composite C-Hub right 4° graphite (ECS)

Composite C-Hub left 4° graphite (ECS)

ANTI-ROLL BAR FRONT 1.2 MM

ANTI-ROLL BAR FRONT 1.3 MM

ANTI-ROLL BAR FRONT 1.4 MM

ANTI-ROLL BAR FRONT 1.6 MM

ANTI-ROLL BAR FRONT 1.8 MM

ADJ. TURNBUCKLE L/R 40 MM - HUDY SPRING STEEL (2)

ALU ADJ. TURNBUCKLE M3 L/R 39 MM - ORANGE - SWISS 7075 T6 (2 pieces)

BALL END 4.9MM WITH THREAD 10MM (2 pieces)

Replacement for the spring steel ball heads with thread. You need to combine them with a standard set crew. So you will be able to modify the thread length by yourself. The usage of thread lock is recommended! What's the advantage of this ball heads? 1. You will save weight. 2. You will save money. No need for a lot of different lengths.