The Body Downtravel Limiter set gives the possibility to setup an bodyshell downtravel stop via the included SC2x15 screws. It reduces bodyshell scrubbing on the ground and tire contact on the inside of the shell. The advantages are better high speed steering and increased stability. The length of the SC2X15 screws in this set is optimal for the most popular current TC...

Front and rear belt is the same when used with the MMCX Conversion Kit.

Front and rear belt is the same when used with the MMCX Conversion Kit.

BW10 Weight to install at the electronics side on AM177 Motormount. contains:

The BW22R Battery Holder set (2pcs) is especially designed for the use of ULCG Batteries (Stick Type) in the A800R Car Platform. This Battery Holders are made of brass material to keep the balance of your car by useing very light ULCG Batteries. Weight: BW22R = 22g per holder (Weight of set = 44g)

Rear stiffener which will also rise the total weight bei 27g.

The BW52R Battery Holder set (2pcs) is especially designed for the use of Shorty Batteries (and ULCG Shorty) in the A800R Car Platform. This Battery Holders are made of brass material to keep the balance of your car by useing Shorty Batteries. Weight: BW52R = 52g per holder (Weight of set = 104g)

Weight to install at the motor side on AM177 Motormount.

Weight to install at the motor side on AM177 Motormount.

Genuine Awesomatix spare part!

Genuine Awesomatix spare part!

Made of 1.2mm hardened spring steel, the chassis combines previously unmatched lower center of gravity and excellent flex characteristics. Extensive refinement of the production process enabled the required chassis flatness and hardness to be achieved. The result is an incredibly long-lasting chassis that will outlast its carbon and aluminium counterparts due to being more...

Spare part for HRB.

The Flex Carbon Bumper is designed for use with P14-1-R Lower bumper. Requires two pcs ST019 (not included) to connect to the AM278 Bulkheads. The use of ST019 offers different front flex and removes possible tweak of the bulkheads in this area.

Replaces the kit part which is made of composite.

Genuine Awesomatix spare parts!

Spare part for FD.

Genuine Awesomatix spare parts!

C127S-G Top Deck (1pcs) for use with AM177 Motormount. Soft version. Made from 1.5mm Glassfiber Material. Two Top Decks are needed for one car. (Front and Rear) INFO: It's required to modify/sand/shorten the rear ST24 Ballstud thread in the rear Bulkhead. Otherwise you are unable to screw down the Top Deck properly.

Genuine Awesomatix spare parts! C204R = fits front left and rear right C204L = fits front right and rear left This set contains two of each - made for one car.

C204R-1 = fits front left and rear right C204L-1 = fits front right and rear left This set contains two of each - made for one car. It narrows the track width of the car and is especially recommended for lower grip levels. The arms have a "-1" engraved on the lower side for easy identification.

Genuine Awesomatix spare parts! C204R = fits front left and rear right C204L = fits front right and rear left

C204R-1 = fits front left and rear right C204L-1 = fits front right and rear left It narrows the track width of the car and is especially recommended for lower grip levels. The arms have a "-1" engraved on the lower side for easy identification.

Genuine Awesomatix spare parts! C204R = fits front left and rear right C204L = fits front right and rear left

C204R-1 = fits front left and rear right C204L-1 = fits front right and rear left It narrows the track width of the car and is especially recommended for lower grip levels. The arms have a "-1" engraved on the lower side for easy identification.

A800 Carbon Top Deck Stiffener (rear)

Optional Awesomatix A800MMX Long Top Deck. Offers the possibility to change the flex characteristics of the car. Additionally it offers the possibility for cutting between the rear ST019 mounting holes. This will create a split Top Deck similar to the kit version, but with more front flex.

Optional Full Length Top Deck for A800MMX and A800R. Made from 2.0mm Glassfiber Material.

Optional Full Length Top Deck for A800MMX and A800R. Made from 2.0mm Glassfiber Material.

Genuine Awesomatix spare parts!

Spare part for APS when it's used in A800R.

Genuine Awesomatix spare parts!

Spare part for APS when it's used in A800R.

Damper Gauge

Damper Gauge

Awesomatix DT10+1.0 Bearing Housing - provides +1 mm higher position of the diff compared to kit's P110 Bearing Housing. Recommended for use on the rear of the car. Provides more on-power steering and increases rotation at certain track conditions. DT10+1.0 were used by Simon Lauter in his WC2024 winning A800R car.

Spare part for FD.

The FBS set consists of two ball studs. It's a very unique design of a dynamic acting ball stud for the suspension. The O-Ring inside the capsuled steel housing allows a movement of the actual ball stud into every direction. Furthermore the O-Ring provides the needed damping effect. It can be beneficial in certain conditions, such as lower grip or on very special...

1. FD set provides an additional torsional flex of the car's end where it is installed. 2. FD set provides the adjustable damping of the chassis's deformations caused by the torsional flex. 3.The damping level of the FD set is adjusted by choice of the silicone oil inside the damper and by choice of the pivoting hole on the arm of the FD rotor. FD set is recommended for...

This set also allows the ESC to be placed in front of the motor to reduce the car's moment of inertia. FSS also provides a bit more torsional flex for the front end of the car and a bit less weight. Additionally the range for Ackermann is extended to 1,5mm instead of the 1,0mm from the std steering set.

GD2 Satellite Gear x 4

GD 2 Bevel Gear x 2

A800 Gear Diff Set Already including the new outdrives ST23X and new sealings P46R Replaces GDB2

The Horizontal Rear Bodypost Set (HRB) lowers the center of gravity. This improves the handling and cornerspeed of your car which leads to faster laptimes. Furthermore the bodyshell will become more stiff in the rear end section and has less deflection at high speed at thus. Fits all A800 models beside A800FX.

IFJ was designing for reducing of the friction between the spool outdrives and the dogbones. Due to the reduced friction in IFJ the front suspension is also a bit softer and smoother on power and under braking. According to reports from tests drivers IFJ are "super to drive, smoother and provide a bit more steering, faster laptimes and less noise". IFJ have good reliability...

IRJ reduces the friction between the outdrive and the dogbone. It increases the efficiency of whole transmission which is an advantage in all situations. Especially in Stock classes the combination of IFJ and IRJ systems will improve the acceleration to the Topspeed. Due to the reduced friction in IRJ the suspension is softer and smoother at car's acceleration and braking....

GD O-Ring x 2

GD O-Ring Soft x 2

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

5mm O-Ring x 4

Spare part for FBS

Genuine Awesomatix spare parts!

13mm O-Ring

OR14V Suspension Arm O-Rings are designed to replace the P07 Arm clip. The advantages are less weight, more reliable at accidents, and at certain conditions more grip due to elasticity at suspension action.

Genuine Awesomatix spare parts!

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

Spare parts for ST122-1 damper screws.

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts!