The Schumacher Fusion Slim 2WD front tyre is developed from the popular Low Profile Cut Stagger. It adds centre spikes for more steering and longer life, but maintains the Stagger edges and undercut sidewall. Therefore allowing any extra steering to be controllable and not too aggressive. It is most suitable for high grip tracks, such as carpet or astro, and can knock tenths...

The Schumacher Fusion Slim 2WD front tyre is developed from the popular Low Profile Cut Stagger. It adds centre spikes for more steering and longer life, but maintains the Stagger edges and undercut sidewall. Therefore allowing any extra steering to be controllable and not too aggressive. It is most suitable for high grip tracks, such as carpet or astro, and can knock tenths...

The Shard is designed for the front of 1/10th 4WD vehicles. Based on the very successful Fusion the new 4WD Shard has been developed to give the ultimate steering with good balance on high bite surfaces. With our classic stagger pattern now utilizing a modernised geometry the Shard will enable the 4WD to have steering exactly where you need it. Schumacher Offroad Tires - one...

The new super thin double-sided adhesive pads have dimensions of 40x40x0.2mm and allow the CCL battery weights, CCL Shorty battery weights and Flow ESC weights to be attached to the bottom of the battery or speed controller with only a minimal increase in the center of gravity. 10 pads, each 40x40mm size, 160cm² in total

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The CCL battery weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution, regardless of which battery type is used, while also lowering the center of gravity. The lower center of gravity...

The flow regulator weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution and at the same time lowers the center of gravity. The lower center of gravity improves the handling of your...

The flow regulator weight is made of black burnished brass with a high specific weight. LRP has made some improvements, such as optimized dimensions and nicely rounded corners. The weight allows the chassis to be perfectly tuned to the ideal weight distribution and at the same time lowers the center of gravity. The lower center of gravity improves the handling of your...

The WorksTeam Gold connectors have particularly flat solder bases, a very low internal resistance and are extremely conductive. The special gold alloy ensures a very low contact resistance.

The WorksTeam Gold connectors have particularly flat solder bases, a very low internal resistance and are extremely conductive. The special gold alloy ensures a very low contact resistance.

The WorksTeam Gold connectors have particularly flat solder bases, a very low internal resistance and are extremely conductive. The special gold alloy ensures a very low contact resistance.

The WorksTeam Gold connectors have particularly flat solder bases, a very low internal resistance and are extremely conductive. The special gold alloy ensures a very low contact resistance.

The unique shape of the specially designed tip makes it easy to attach and remove tiny E-rings.

The idea behind these gold plugs is as simple as it is ingenious! A perfect connection between the controller and the battery is absolutely essential. Many drivers spend so much money on batteries and controllers to get the last bit out of their drive and then ignore the gold plugs. There are differences in the batteries and the plug is subject to "wear and tear". Those who...

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Special silicone-based grease to achieve a controlled locking effect when using cone differentials. It is also often used by PanCar drivers (e.g. with the Awesomatix A12) on the KingPin front axle to create a certain inertia through the grease and thus create a type of damping on the front axle.

Special silicone-based grease to achieve a controlled locking effect when using cone differentials. It is also often used by PanCar drivers (e.g. with the Awesomatix A12) on the KingPin front axle to create a certain inertia through the grease and thus create a type of damping on the front axle.

Special silicone-based grease to achieve a controlled locking effect when using cone differentials. It is also often used by PanCar drivers (e.g. with the Awesomatix A12) on the KingPin front axle to create a certain inertia through the grease and thus create a type of damping on the front axle.

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Genuine Team Associated parts - the best solution for your Asso car!

Front tires: 63mm diameter 28mm width for bearings Rear tires: 63mm diameter 50mm width standard hub with 4 screws Will be sold as a set of two tires. Glued on grey star rims.

8-channel computer pistol-grip RC set RadioLink using a FHSS 2.4GHz transmission system for model cars and boats. With the R8FG FHSS telemetry receiver included in the set, you have 8 PWM channels for conventional servos plus a built-in gyro. The RC8X transmitter can also work with the R6F and R6FG 6-channel receivers with built-in gyro, the R4FGM and R4F 4-channel...

PIP-Aero is a product developed and manufactured entirely in Germany. Design, mold making and production take place in Germany. The implementation is of very high quality and always carried out from the perspective of the absolute thoroughbred racer. Scale: 1:10 Width: approx. 194mm front / 191mm rear Wheelbase: approx. 265mm Scope of delivery: Body Window masking Decal...

PIP-Aero is a product developed and manufactured entirely in Germany. Design, mold making and production take place in Germany. The implementation is of very high quality and always carried out from the perspective of the absolute thoroughbred racer. Scale: 1:12 Width: approx. 176mm Wheelbase: approx. 200mm Scope of delivery: Body Window masking Decal sheet Available in...

PIP-Aero is a product developed and manufactured entirely in Germany. Design, mold making and production take place in Germany. The implementation is of very high quality and always carried out from the perspective of the absolute thoroughbred racer. Scale: 1:12 Width: approx. 176mm Wheelbase: approx. 200mm Scope of delivery: Body Window masking Decal sheet Available in...

The Tamiya Group C chassis does not include a foam front bumper as standard. As long as the chassis is just on the shelf, this does not play a major role. Unfortunately, when it goes on the track, the front may be stronger because it cannot be cushioned. The tuning front bumper consists of a carbon base that is dimensioned so large that it supports the foam bumper on top of...

Width: approx. 29mm Inner diameter: approx. 44mm Outer diameter: approx. 62mm Mixture: HI (special for asphalt with less rear grip) Hardness: 35 Shore

Suitable for the HUDY Car Stand version 108150, 108160 or 108170.

Square Alloy and Titanium screws - available in many different colours and sizes.

Square Alloy Nuts- available in many different colours and sizes.

High quality silicon oil - for a constant setup. AXON oils are resistent to high temperatures therefore the diff stays stable for a very long time before it has to be refreshened. The oils are available in consistencies of 1.000 up to 30.000 cSt. The lower the number, the thinner the oil.

Original spare and optional parts!

Front tires: 45mm diameter 26mm width for bearings Rear tires: 46mm diameter 38mm width standard hub with 3 screws Which compound should I choose? Front: 30, 32, 35, 37 Shore: standard foam for indoor and outdoor use Hagberg: special foam which works on nearly any carpet just perfect Hagberg Red Dot: special foam, made for ETS carpet Rear: 30, 32, 35 Shore: standard foam for...

Genuine Awesomatix part! Tech Tipp for A12 drivers which are searching for C1205-1.5: C1205X has the exact same sizes as C1205-1.5 except for the 1,25 mm depth recess for front pivot balls. So C1205X is a direct replacement. Customers just need to turn the plate in the direction to have the milled out area on the upper side and the flat surface on the lower side.

Power Connector Charger: XT90 Balancer Connector Charger: XH Power Connector Battery: 4/5mm Balancer Connector Battery: 2mm Total length: ca. 50cm

Power Connector Charger: XT90 Power Connector Battery: T-Plug Total length: ca. 30cm

Ball Diff Grease - 10ml

Genuine Team Associated parts - the best solution for your Asso car!

Suitable for 1/10 touring Outer Diameter: 62.5mm Width: 24mm For all those guys who want to use their own tires.

Genuine SANWA spare part!

Take care: This a German RC Car magazine. It's written in GERMAN language. So we decided to offer a German only description.

Front tires: 63mm diameter 28mm width for bearings Rear tires: 63mm diameter 50mm width standard hub with 4 screws Will be sold as a set of two tires. Glued on grey star rims.

Suitable for the HRC 58W soldering station HRC4091B.

Suitable for the HRC 58W soldering station HRC4091B.