A800FX Stickers Sheet

A800MMX Stickers Sheet

Will also fit to any kind of A700 / A800. A bit wider and longer than the old A800 standard part.

Genuine Awesomatix spare parts! AM08-3 Shocks Holder for A800MMX/A800MMXA. Used in front of the car to increase chassis frame flex. Also suitable for A800/X/Evo car kits. contains: 1pcs AM08-3

Genuine Awesomatix spare parts!

Spare part for the MMCX-2 kit. Can be used also as optional for the old MMCX kit.

Optional part for the MMCX kit. Will allow different flex settings in the back of the car.

AM105H MMX Rear Stiffener. Heavier version (30g. total weight) of AM105. Useable with all Middle Motor chassis.

Spare Part for DL

Spare part for HRB.

Official replacement for AM12-1 - with a higher range of settings for different kind of batteries (like LCG).

Genuine Awesomatix spare parts!

AM14H Steering Arms are a special stronger version of the AM14LS steering arms (same footprint). Recommended to use when racing on tracks with click-track / hard boards.

Especially made for the new LS1. Can be also used without LS1. Without LS1 also for A700 suitable!

Battery Nut x 2

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts!

AM177-2 Motor Mount for A800MMX/A made from high grade 7075 T6 alloy. The new version features an increased slot for the ESC wire to allow an easier electronics installation. Additionally, the AM177-2 has the Belt Anti Skip unit integrated To make use of this, you need additionally 1x B73SS ball bearing and 1x SB3X5 screw. (INFO - A800-BAS set is not suitable to use with...

Alu Damper Holder The range of adjustment for A and B is reduced, compared to the old A800 parts. Please make sure not to mix up!

Alu Damper Holder The range of adjustment for A and B is reduced, compared to the old A800 parts. Please make sure not to mix up!

AM180EVO2 SB Bellcrank for the Single Bellcrank Steering. The EVO2 version is an updated design of the EVO version and features an additional screw on top that secures the bearings in the alloy part and avoids a bearing shift at high force impacts. INFO: AM180EVO2 is only compatible with ST118L-1 !

The EVO version is equipped with the same bigger bearings as the M5 version to further increase the reliability. Furthermore the height of the AM180EVO is slighlty adjusted to avoid contact with P12X at certain setups. By this change, less bumpsteer shims are needed on the steering arm, which reduces the stress in this part. To keep the same bumpsteer value as with AM180M5...

Genuine Awesomatix Spare Parts!

IAS Steering Arm x2

Awesomatix A700-AM23-1 - Rear Steering Arm x 2

This version is longer compared to the previous AM23-1 Rear Steering Arm. This feature reduces the free play of the rear toe and improves ARS characteristics. The improved characteristics of the ARS helps with better midcorner steering and reduce the risk of snap oversteer during load changes. We recommend to use 0,5mm less bumpsteer shims, to keep the same ARS action as...

AM24-20 optional Servo Holder for all A800 car models (beside A800FX) in combination with SB1 Steering. This new designed part combine servo holder and steering holder to one single part. It offers a more equal chassis flex as the Servo holder doesn't need to be screwed outside of the chassis center line.

Genuine Awesomatix Spare Parts!

Rear Ball Holder x 2

Genuine Awesomatix Spare Parts! You want to convert your existing A800FX into an A800FX EVO? No problem. You will need: C01FXAL or C01FXCL AM24FX AM180FX 2x AM78FX AM30FX AT159 C27FX-S For a full conversion you should add also: C107S ST230 If your car does not already include you may also upgrade to: ST69-00 and AT119 C15A D2.2-S-P

A800 Alu Steering Bellcrank (including bearings)

Genuine Awesomatix spare parts!

Spare parts for cars using the MMCX conversion kit.

Direct replacement for AM77X. It includes a holder for DL / DL-A and offers a 0.5mm gap in the rear for a different flex setting.

Genuine Awesomatix Spare Parts! Please note: It's a standard AM78X1 Bulkhead which has been modified. The modified area is not anodized anymore. Can be also used in A800FX.

A800X Alu Bulkhead (1 piece) Direct replacement for AM78, AM78X and AM78X1 If you want to replace an old one we recommened to change always both. AM78X3 Bulkhead made from high grade 7075 T6 alloy. This version features slightly modified end tips to further extend the clearance of the steering link at full lock under suspension up travel. It's a direct replacement for AM78X1...

Spare part for LS1

Spare Parts for LS2 There is a mistake in the manual. AT862 doesn't exist. AT862 = AM862

Spare Parts for LS2

A800 Alu Shock Holder - left

A800 Alu Shock Holder - right

VTD Holder

Servo Gear Set - will fit to AS-700L and AS-701L as well.

Alu Spool Axle. Will fit only to P138S / P138LFS and must be used with SB3X5 Screws! Then it's possible to use in A800, too. Replacement for AT03B - please use new pulley and bigger screws as described above.

New spool design with reduced weight (only 2,6g.) and improved rigidity. Only compatible with P138A / P138A-LF Pulley (3pcs SC2x4 needed!)

Antenna Holder

Replacement part for PSS.

Replacement part for PSSX

Genuine Awesomatix spare parts! The ball bearings are already installed. We don't recommend to change them by yourself. It's recommened to get a complete new pulley. If you want to try it by yourself you will need the bearings B106RS and B84RS (one of each).

A800 Alu 20T Pulley Including Ball Bearings (B106RS, B84RS). Direct replacement for AT120. More reliable and precise. The old spare parts AT120-1, DT08, AT67 and AT62 doesn't fit anymore!

A800 GD2B Case 1

A800 GD2B Case 2

Wheel Hex x 2

AT139 Fan Holder for A800MMX and A800FX models. Can be screwed directly to the Motormount (AM177 / AM77FX) to install and secure 30mm & 35mm fans.

Genuine Awesomatix spare parts!

Wheel Hex x 2

Turnbuckle - M3 x 27mm - (4pcs)

Alu Stopper

AT144 ULCG Battery Clamp (2pcs) is specially designed for the use of modern ULCG style Lipos batteries. They are machined of 7075 T6 alloy and offer a lower profile than the std. plastic battery holders. Also recommended to use with the BW22 / BW52 Battery Holders. contains 2pcs A800-AT144

Can be used to reduce the play in the hubs.