Genuine Awesomatix spare parts!

Spare part for ADC. It's already included in the ADC set.

Genuine Awesomatix Spare Parts!

Steering Limiter for useing with Bellcrank Steering (BSSX) AT18 has two modes of steering angle limiting 1) for carpet, 2) for asphalt. These two limits are based on data and setups from our team drivers. Designed for AM79A only. Check the pictures if you want to know if you have AM79 or AM79A.

Awesomatix A700-AT21S/4 - Pivot Ball Short x4 Steel Version of AT21S. Same height as AT21S. Features a hole on top to fit a 2.0mm allen wrench.

AT25-2 is set of 2x 39mm length Turnbuckles. This optional set can be used as replacement for AT14 parts at the rear "Toe-In Turnbuckles". The thread will go more deep inside of P13-4 Ball Cups and secure the "Toe-In" stay more consistent at impacts. Contains 2pcs of AT25-2

The standard AT25 (which is 6mm shorter than this one) is near to the limit when using AM14LS with bellcrank steering and longer suspension arms (+0.5 and especially +1.5). AT25-44 will solve this issue. Set of four pieces.

Battery Post x2 Short version for ULCG batteries with 18.5mm battery height.

Awesomatix A700-AT40-1 - Damper Cup

Spare part for ADC.

Damper vane for SPR02H3

Awesomatix A700-AT42-1 - Damper Case

A800 Alu Spur Nut AT55M is a more narrow version of AT55. Spezial designed for the Middle Motor conversion. Can be also used in all A800 and A800X Cars as option

A800 Alu Belt Tensioner

Take care: It's not easy to replace. Think of replacing AT120 als complete unit.

A800 Pulley Washer

Replacement for the ABS set.

Spare part for LS1 Has been shown as AT73 at the beginning. This was a mistake. Correct number is AT71.

Spare Parts for LS2

Sparepart for AT74

AT78 should be used with OR152 O-Ring. Only compatible to D2.2 dampers. Will replace the P45L sponge.

Spare Part for DL-A

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 6x10x3 x2

4x1.5mm ball bearings x 8

Awesomatix A700-B63SS - MR63ZZ Bearing 3x6mm (2 pcs)

Bearing for LS2 - 7x2.5x3mm - (2pcs) Spare Parts for LS2 Is shown in the manual as B73RS

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 4x8x3 x 2 Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.

Bearing 5x8x2.0 x 2

The Belt Anti Skip set (BAS) is designed for Modified racing purpose with "big horsepower" and/or high traction conditions. It will support the rear belt with an additional ballbearing and prevents 100% from Belt skipping in every possible scenario. Info: This part/set fits only with AM177 Motormount. Take care: In the manual this item is shown as AM111. AM111 is only the...

13x 6x10mm 1x 4x8mm

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side. BBS-1C set includes: B106RC/Z -...

Awesomatix A700-BC1 - Battery Clamps Set V2019 with short posts for ULCG batteries (18.5mm battery height). If you want to user standard or LCG batteries (25mm / 22.5mm height) you need to use additional shims which are not included.

The Body Downtravel Limiter set gives the possibility to setup an bodyshell downtravel stop via the included SC2x15 screws. It reduces bodyshell scrubbing on the ground and tire contact on the inside of the shell. The advantages are better high speed steering and increased stability. The length of the SC2X15 screws in this set is optimal for the most popular current TC...

A800 BANDO Rear Belt - 189mm

A800 BANDO Rear Belt - 189mm

Genuine Awesomatix spare parts!

Front and rear belt is the same when used with the MMCX Conversion Kit.

Front and rear belt is the same when used with the MMCX Conversion Kit.

A800 BANDO Front Belt - 513mm

A800 Front Belt - 513mm

BW10 Weight to install at the electronics side on AM177 Motormount. contains:

The BW22 Battery Holder set (2pcs) is especially designed for the use of ULCG Batteries (Stick Type) in the A800 Car Platform. This Battery Holders are made of brass material to keep the balance of your car by useing very light ULCG Batteries. BW22 is designed for the use with carpet/high traction oriented alloy chassis. Weight: BW22 = 22g per holder (Weight of set = 44g)...

The BW52 Battery Holder set (2pcs) is especially designed for the use of Shorty Batteries (and ULCG Shorty) in the A800 Car Platform. This Battery Holders are made of brass material to keep the balance of your car by useing Shorty Batteries. BW52 is designed for the use with carpet/high traction oriented alloy chassis. TIP: We recommend to mount BW52 with 0,2-0,5mm shims...

Weight to install at the motor side on AM177 Motormount.

Weight to install at the motor side on AM177 Motormount.

BW95 is a new Floating Front Weight for the A800FX & A800FX Evo cars. This additional weight helps to adjust the front/rear weight distribution of the car for different track conditions. Additionally it improves the front flex of the car, as BW95 replaces the AM88//R Shock Holders. This improved front flex helps with better overall steering and front end grip! BW95 doesn't...

A800 Carbon Lower Deck - 2.25mm

A800 Alu Lower Deck - hart

Special version for the long suspension arms (C04M1+9.0 and C04M1+8.0). The longer suspension arms are great when traction is needed. It still features mounting holes for the short standard arms - so you can use both! Can be used also in the old A800. You need to change additionally: - P12X - B63SS - AT142 Should be used only with the new lower suspension arms (C04M1,...

Special version for the long suspension arms (C04M1+9.0 and C04M1+8.0). The longer suspension arms are great when traction is needed. It still features mounting holes for the short standard arms - so you can use both! Whats the difference between V1 and V2? The Cutouts/Design is changed to offer more response and better steering feeling combined with the high corner speeds...

Genuine Awesomatix spare parts!

Genuine Awesomatix Spare Parts!

Medium option. Softer than the kit Alloy. Stiffer than the C01FXR-C Carbon.

Will also fit to any kind of A700 / A800. C04AL+0.5 has been replaced by C04AL1+0.5. They should not be mixed. Same geometry, different shape. 0.5mm longer than C04AL1. A longer suspension arm will offer more overall grip and traction.

Will also fit to any kind of A700 / A800. These arms are mainly for low-med traction conditions. We will use these arms with AT21+0.5S balls in narrow position to keep the overal width within the legal 190mm. For more grip on rear end ( easy to drive car) you shoul use C04AL1+1.5 on rear with C04AL1+0.5 on front ( front balls are as usuall for these arms). For more steering...

+9.0mm will be usually used in the front +8.0mm will be usually used in the rear INFO: Only suitable for following Chassis -> C01B-X-LA / C01B-XA-LA / C01B-XAH-LA / C01B-XAH2-LA / C01B-X-MM

+9.0mm will be usually used in the front +8.0mm will be usually used in the rear INFO: Only suitable for following Chassis -> C01B-X-LA / C01B-XA-LA / C01B-XAH-LA / C01B-X-MM

+9.0mm will be usually used in the front +8.0mm will be usually used in the rear INFO: Only suitable for following Chassis -> C01B-X-LA / C01B-XA-LA / C01B-XAH-LA / C01B-X-MM