C04M1-LA Long Arm Set includes: 2x C04M1+9.0 2x C04M1+8.0 INFO: Only suitable for following Chassis -> C01B-X-LA / C01B-XA-LA / C01B-XAH-LA / C01B-X-MM

Spare part for HRB.

C07A - Carbon Bumper A is designed for use with P14-1X Lower bumper. The new design offer support to Bulkheads to prevent Chassis from bending on front area at Crashes. This part don't allow combination with normal P14. You will need 4x SH175 shims + 2x SB3X6 screw to use the support. With the latest change (V3) Awesomatix updated the footprint just a little bit. They...

Genuine Awesomatix spare parts!

This part will allow to adjust the height of the rear body posts. Standard height is the same like C105. It's possible to adjust +/- 3mm.

Genuine Awesomatix spare parts!

Genuine Awesomatix Spare Parts!

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts!

C127S-G Top Deck (1pcs) for use with AM177 Motormount. Soft version. Made from 1.5mm Glassfiber Material. Two Top Decks are needed for one car. (Front and Rear) INFO: It's required to modify/sand/shorten the rear ST24 Ballstud thread in the rear Bulkhead. Otherwise you are unable to screw down the Top Deck properly.

Optional link for VTD set. It blocks the side movement of the VTD. Same as ST55 in diagonal position for normal C27X deck. You will need 2x ST019 special screw to use it! They are NOT included. Suitable for A800 and A800X.

A800 Carbon Top Deck Stiffener (rear)

Genuine Awesomatix spare parts!

Genuine Awesomatix Spare Parts!

Optional Awesomatix A800FX Evo Long Top Deck. Also suitable for A800FX car. Offers the possibility to change the flex characteristics of the car. Additionally it offers the possibility for cutting between both rear ST019 mounting holes. This will create a split Top Deck similar to the kit version, but with more front flex.

Spare part for the MMCX-2 kit. Can be used also as optional for the old MMCX kit.

C27MMS-1 Top Deck for A800X Middle Motor conversion. This Version is softer and offer more flex than C27MM2. It's designed to be used with AM102 Top Deck Stiffener. The holes for screwing AM102 are designed to allow the use of normal SB3x5 screws, as well ST019 Top Deck Screws. This allow to use different flex options in this area. Specialy recommended for use with...

Optional Awesomatix A800MMX Long Top Deck. Offers the possibility to change the flex characteristics of the car. Additionally it offers the possibility for cutting between the rear ST019 mounting holes. This will create a split Top Deck similar to the kit version, but with more front flex.

Optional Full Length Top Deck for A800MMX and A800R. Made from 2.0mm Glassfiber Material.

Optional Full Length Top Deck for A800MMX and A800R. Made from 2.0mm Glassfiber Material.

Graphite Upper Deck

For Awesomatix DL and DL-A. Can be used as replacement for C27X

VTD Topdeck

Genuine Awesomatix spare parts!

C36 include 2pcs of 2.0mm thick carbon spacers to mount between chassis and Battery Holders. This option part raise the whole Battery Holder by 2mm and secure better hold for Batteries with recess areas at the plug side.

Awesomatix A700-D2.1 - Damper

Damper Gauge

Damper Gauge

The diagonal link reduces the S-type bending of chassis but doesn't affect on the torsional flex. DL set set includes: C27X - 1 pcs AM107 - 1 pcs AT74 - 1 pcs ST019 - 1 pcs AT21S - 1 pcs P13-4 - 2 pcs SB3X8 - 2 pcs SS3X8 - 1 pcs

The diagonal link reduces the S-type bending of chassis but doesn't affect on the torsional flex. DL set set includes: C27X-1 - 1 pcs AT97 - 1 pcs AT21 - 2 pcs ST019 - 1 pcs P13-4 - 2 pcs SF3X8 - 1 pcs

Awesomatix DT10+1.0 Bearing Housing - provides +1 mm higher position of the diff compared to kit's P110 Bearing Housing. Recommended for use on the rear of the car. Provides more on-power steering and increases rotation at certain track conditions. DT10+1.0 were used by Simon Lauter in his WC2024 winning A800R car.

A800 Bearing Housing (2 pieces) DT10-2-1 is the replacement for DT10-2-1 which has been slightly modified.

A800 Bearing Housing (2 pieces) DT10-2 is the replacement for DT10 which has been slightly modified.

Spare part for LS1

Spare part for LS1

The FBS set consists of two ball studs. It's a very unique design of a dynamic acting ball stud for the suspension. The O-Ring inside the capsuled steel housing allows a movement of the actual ball stud into every direction. Furthermore the O-Ring provides the needed damping effect. It can be beneficial in certain conditions, such as lower grip or on very special...

GD2 Satellite Gear x 4

GD 2 Bevel Gear x 2

A800 Gear Diff Set Already including the new outdrives ST23X and new sealings P46R Replaces GDB2

The Horizontal Rear Bodypost Set (HRB) lowers the center of gravity. This improves the handling and cornerspeed of your car which leads to faster laptimes. Furthermore the bodyshell will become more stiff in the rear end section and has less deflection at high speed at thus. Fits all A800 models beside A800FX.

IFJ was designing for reducing of the friction between the spool outdrives and the dogbones. Due to the reduced friction in IFJ the front suspension is also a bit softer and smoother on power and under braking. According to reports from tests drivers IFJ are "super to drive, smoother and provide a bit more steering, faster laptimes and less noise". IFJ have good reliability...

IRJ reduces the friction between the outdrive and the dogbone. It increases the efficiency of whole transmission which is an advantage in all situations. Especially in Stock classes the combination of IFJ and IRJ systems will improve the acceleration to the Topspeed. Due to the reduced friction in IRJ the suspension is softer and smoother at car's acceleration and braking....

14mm O-Ring

GD O-Ring x 2

GD O-Ring Soft x 2

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

5mm O-Ring x 4

FCB O-Ring x 2

O-Ring 9mm

Spare part for FBS

13mm O-Ring

OR14V Suspension Arm O-Rings are designed to replace the P07 Arm clip. The advantages are less weight, more reliable at accidents, and at certain conditions more grip due to elasticity at suspension action.

Awesomatix A700-OR152 - 2x1.5mm U-Ring Will be used for AT78. OR152S can be installed in any direction but I prefer the open side of the U into shock.

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

Awesomatix A700-OR15M - Damper Output O-Ring

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

This O-Ring is made out of a new rubber material which is even more durable and less affected by silicon oil. The "V" O-Rings are easy to distinguish as they have a slight shade of brown.

Ball Joint-1 x 4

Ball Joint-2 x 4

Arm Ball Cap x 5