AT78 should be used with OR152 O-Ring. Only compatible to D2.2 dampers. Will replace the P45L sponge.

Bearing 6x10x3 x2

2.4mm Ball x 17

4x1.5mm ball bearings x 8

Bearing 4x7x2,5 x 2

Bearing 4x8x3 x 2 Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.

Bearing 5x8x2.0 x 2

Awesomatix A700-B85RS - MR85RS Bearing 5x8mm (2 pcs) Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.

Awesomatix A700-BC1 - Battery Clamps Set V2019 with short posts for ULCG batteries (18.5mm battery height). If you want to user standard or LCG batteries (25mm / 22.5mm height) you need to use additional shims which are not included.

The Body Downtravel Limiter set gives the possibility to setup an bodyshell downtravel stop via the included SC2x15 screws. It reduces bodyshell scrubbing on the ground and tire contact on the inside of the shell. The advantages are better high speed steering and increased stability. The length of the SC2X15 screws in this set is optimal for the most popular current TC...

2,2mm Carbon Chassis for A700L2 and A700 Evo II cars. C01L2L Lower Deck is suitable also for long arms installation. We recommend to start with C04M1+8.0 arms or C04AL1+8.0 arms on front and on rear. Can be used only with MM2 - Evo II Motor Mount Set.

Awesomatix A700-C02-2 - Top Deck L2

Top Deck T

Will also fit to any kind of A700 / A800. C04AL+0.5 has been replaced by C04AL1+0.5. They should not be mixed. Same geometry, different shape. 0.5mm longer than C04AL1. A longer suspension arm will offer more overall grip and traction.

Will also fit to any kind of A700 / A800. These arms are mainly for low-med traction conditions. We will use these arms with AT21+0.5S balls in narrow position to keep the overal width within the legal 190mm. For more grip on rear end ( easy to drive car) you shoul use C04AL1+1.5 on rear with C04AL1+0.5 on front ( front balls are as usuall for these arms). For more steering...

C07A - Carbon Bumper A is designed for use with P14-1X Lower bumper. The new design offer support to Bulkheads to prevent Chassis from bending on front area at Crashes. This part don't allow combination with normal P14. You will need 4x SH175 shims + 2x SB3X6 screw to use the support. With the latest change (V3) Awesomatix updated the footprint just a little bit. They...

FFG Top Deck Link

FFG Top Deck Narrow

FFG Carbon Rod

FFG Carbon Rod soft

C36 include 2pcs of 2.0mm thick carbon spacers to mount between chassis and Battery Holders. This option part raise the whole Battery Holder by 2mm and secure better hold for Batteries with recess areas at the plug side.

Awesomatix A700-D2.1 - Damper

Diff Cover S Set

Damper Gauge

Damper Gauge

Diff Cage

Bearing Housing x 4

Motor Mount Collar

FFG Collar x2

The FBS set consists of two ball studs. It's a very unique design of a dynamic acting ball stud for the suspension. The O-Ring inside the capsuled steel housing allows a movement of the actual ball stud into every direction. Furthermore the O-Ring provides the needed damping effect. It can be beneficial in certain conditions, such as lower grip or on very special...

22T Bevel Gear

27T Bevel Gear

25T Bevel Gear

20T Plastic Gear x 2

20T Steel Gear x 2

10T Steel Gear x 4

GD2 Satellite Gear x 4

GD 2 Bevel Gear x 2

IFJ was designing for reducing of the friction between the spool outdrives and the dogbones. Due to the reduced friction in IFJ the front suspension is also a bit softer and smoother on power and under braking. According to reports from tests drivers IFJ are "super to drive, smoother and provide a bit more steering, faster laptimes and less noise". IFJ have good reliability...

IRJ reduces the friction between the outdrive and the dogbone. It increases the efficiency of whole transmission which is an advantage in all situations. Especially in Stock classes the combination of IFJ and IRJ systems will improve the acceleration to the Topspeed. Due to the reduced friction in IRJ the suspension is softer and smoother at car's acceleration and braking....

BD O-Ring x 2

11mm O-Ring

14mm O-Ring

U-Ring for #6 and #3 dampers x 4

FCB O-Ring x 2

Spare part for FBS

Awesomatix A700-OR152 - 2x1.5mm U-Ring Will be used for AT78. OR152S can be installed in any direction but I prefer the open side of the U into shock.

Awesomatix A700-OR15M - Damper Output O-Ring

Ball Joint-1 x 4

Ball Joint-2 x 4

Arm Ball Cap x 5

Arm Ball Cap x 5

Arm Hasp x 4

Sway Bar Joint x 4

Downstop Collar x 5

Arm Clip x 10

P09X set is for "progressive" settings of the springs. P09X set includes 4 pcs of P09X plastic parts and 4 pcs of DIN915 M3X3 set screws. One of additional holes is for DIN915 M3X3 screw and has 3,1 mm distance to the main RHS screw. The opposite additional hole is for RHS-P M2 screw and has 3,7 mm distance to the main RHS screw. Please notice the helpful manual which is...

Diff Cover x2

Sway bar mount. Can be used on old A800 kits, but it is necessary to change also: - lower deck (C01B-X, C01B-XA, C01B-XAH) - sway bar stopper AT142 - ball bearings B63SS You may need also different standard screws. Should be used only with the new lower arms (C04M1, C04AL1)

Ball End x 2