Optional Alloy Battery Holders for A800R. Width for battery adjustable via sliding the AM280R in and out. Length for battery adjustable via P68 Battery adjusters (kit parts). Only suitable for A800R. Total weight: ~6g.

Will also fit to any kind of A700 / A800. A bit wider and longer than the old A800 standard part.

Spare part for HRB.

Genuine Awesomatix spare parts!

Especially made for the new LS1. Can be also used without LS1. Without LS1 also for A700 suitable!

Spare part for the ABH set.

AM177-2 Motor Mount for A800MMX/A made from high grade 7075 T6 alloy. The new version features an increased slot for the ESC wire to allow an easier electronics installation. Additionally, the AM177-2 has the Belt Anti Skip unit integrated To make use of this, you need additionally 1x B73SS ball bearing and 1x SB3X5 screw. (INFO - A800-BAS set is not suitable to use with...

AM180EVO2 SB Bellcrank for the Single Bellcrank Steering. The EVO2 version is an updated design of the EVO version and features an additional screw on top that secures the bearings in the alloy part and avoids a bearing shift at high force impacts. INFO: AM180EVO2 is only compatible with ST118L-1 !

The EVO version is equipped with the same bigger bearings as the M5 version to further increase the reliability. Furthermore the height of the AM180EVO is slighlty adjusted to avoid contact with P12X at certain setups. By this change, less bumpsteer shims are needed on the steering arm, which reduces the stress in this part. To keep the same bumpsteer value as with AM180M5...

Spare part for FSS.

In normal positions these holders provide +1mm longer top link compared to AM19R. Reverse mounting is also possible to get extra long top links which are ~10mm longer than AM19R. (requires optional AT25-2 turnbuckles!). It also offers an intermediate mounting position which provides ~8mm longer top links. AM19-LTL should be mounted reverse for that. One link mounted on the...

Genuine Awesomatix spare parts!

Awesomatix A700-AM23-1 - Rear Steering Arm x 2

This version is longer compared to the previous AM23-1 Rear Steering Arm. This feature reduces the free play of the rear toe and improves ARS characteristics. The improved characteristics of the ARS helps with better midcorner steering and reduce the risk of snap oversteer during load changes. We recommend to use 0,5mm less bumpsteer shims, to keep the same ARS action as...

AM24-20 optional Servo Holder for all A800 car models (beside A800FX) in combination with SB1 Steering. This new designed part combine servo holder and steering holder to one single part. It offers a more equal chassis flex as the Servo holder doesn't need to be screwed outside of the chassis center line.

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts! Ball bearings already included.

Genuine Awesomatix spare parts! Ball bearings are already included.

Spare part for FSS.

Rear Ball Holder x 2

Updated version of AM278 and direct replacement. Suitable for all A800R cars. Please note the installation info in the gallery. contains: 1pcs AM278-EVO 1pcs SS3X3

Awesomatix AM279 Rear Belt Tensioner for A800R. Mounted on the chassis, right behind the motormount. Further reduces belt skipping on the rear pulley and extends the lifespan of the belts.

Spare part for the ABH set.

Spare part for FD.

The APS - Additional Progressive Spring set is designed for use in the Awesomatix A800R touring car. Progressive conical tapered springs of the APS set press on the lower suspension arms and add a progression into the suspension spring rate. Test results showed more consistent laptimes with improved overall feeling on the low-med grip asphalt and carpet tracks. Two types of...

Alu Spool Axle. Will fit only to P138S / P138LFS and must be used with SB3X5 Screws! Then it's possible to use in A800, too. Replacement for AT03B - please use new pulley and bigger screws as described above.

New spool design with reduced weight (only 2,6g.) and improved rigidity. Only compatible with P138A / P138A-LF Pulley (3pcs SC2x4 needed!)

Antenna Holder

Replacement part for PSS.

Replacement part for PSSX

A800 Alu 20T Pulley Including Ball Bearings (B106RS, B84RS). Direct replacement for AT120. More reliable and precise. The old spare parts AT120-1, DT08, AT67 and AT62 doesn't fit anymore!

A800 GD2B Case 1

A800 GD2B Case 2

Wheel Hex x 2

AT139 Fan Holder for A800MMX and A800FX models. Can be screwed directly to the Motormount (AM177 / AM77FX) to install and secure 30mm & 35mm fans.

Wheel Hex x 2

Turnbuckle - M3 x 27mm - (4pcs)

Alu Stopper

The AT143 ARB Stiffener increases stiffness of the anti-roll bar up to one step. +1 step stiffness increasings means that 1.0 mm bar acts like 1.1 mm bar 1.1 mm bar acts like 1.2 mm bar 1.2 mm bar acts like 1.3 mm bar 1.3 mm bar acts like 1.4 mm bar. 1/2 and 1/4 steps of increasing are possible to set. See Instructions attached as picture. contains: 2pcs AT143 4pcs SS3X3

AT144 ULCG Battery Clamp (2pcs) is specially designed for the use of modern ULCG style Lipos batteries. They are machined of 7075 T6 alloy and offer a lower profile than the std. plastic battery holders. Also recommended to use with the BW22 / BW52 Battery Holders. contains 2pcs A800-AT144

Can be used to reduce the play in the hubs.

Awesomatix A700-AT21S/4 - Pivot Ball Short x4 Steel Version of AT21S. Same height as AT21S. Features a hole on top to fit a 2.0mm allen wrench.

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts!

AT248 reduces the local load on the area of the front bumper center mounting screw on the lower deck. This reduces the chances of a lower deck damage at frontal impacts. Recommended for carbon lower deck in A800R car. Slight modification of the plastic bumper P14-R-1 is needed. For installation cut the center pin on P14-1-R and increase the hole till ID 5mm. Explanation...

AT25-2 is set of 2x 39mm length Turnbuckles. This optional set can be used as replacement for AT14 parts at the rear "Toe-In Turnbuckles". The thread will go more deep inside of P13-4 Ball Cups and secure the "Toe-In" stay more consistent at impacts. Contains 2pcs of AT25-2

The standard AT25 (which is 6mm shorter than this one) is near to the limit when using AM14LS with bellcrank steering and longer suspension arms (+0.5 and especially +1.5). AT25-44 will solve this issue. Set of four pieces.

Battery Post x2 Short version for ULCG batteries with 18.5mm battery height.

A800 Alu Spur Nut AT55M is a more narrow version of AT55. Spezial designed for the Middle Motor conversion. Can be also used in all A800 and A800X Cars as option

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 6x10x3 x2

4x1.5mm ball bearings x 8

Awesomatix A700-B63SS - MR63ZZ Bearing 3x6mm (2 pcs)

Bearing for LS2 - 7x2.5x3mm - (2pcs) Spare Parts for LS2 Is shown in the manual as B73RS

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 4x8x3 x 2 Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.

Bearing 5x8x2.0 x 2

13x 6x10mm 1x 4x8mm

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side. BBS-1C set includes: B106RC/Z -...

Awesomatix A700-BC1 - Battery Clamps Set V2019 with short posts for ULCG batteries (18.5mm battery height). If you want to user standard or LCG batteries (25mm / 22.5mm height) you need to use additional shims which are not included.