Genuine Awesomatix part!

Genuine Awesomatix part!

Genuine Awesomatix part!

GD2 Case1

A800 GD2B Case 1

GD2 Case2

A800 GD2B Case 2

Wheel Hex x 2

AT139 Fan Holder for A800MMX and A800FX models. Can be screwed directly to the Motormount (AM177 / AM77FX) to install and secure 30mm & 35mm fans.

Genuine Awesomatix spare parts!

Wheel Hex x 2

Turnbuckle - M3 x 27mm - (4pcs)

Alu Stopper

The AT143 ARB Stiffener increases stiffness of the anti-roll bar up to one step. +1 step stiffness increasings means that 1.0 mm bar acts like 1.1 mm bar 1.1 mm bar acts like 1.2 mm bar 1.2 mm bar acts like 1.3 mm bar 1.3 mm bar acts like 1.4 mm bar. 1/2 and 1/4 steps of increasing are possible to set. See Instructions attached as picture. contains: 2pcs AT143 4pcs SS3X3

AT144 ULCG Battery Clamp (2pcs) is specially designed for the use of modern ULCG style Lipos batteries. They are machined of 7075 T6 alloy and offer a lower profile than the std. plastic battery holders. Also recommended to use with the BW22 / BW52 Battery Holders. contains 2pcs A800-AT144

Can be used to reduce the play in the hubs.

Genuine Awesomatix spare parts!

Spare part for ADC. It's already included in the ADC set.

Genuine Awesomatix Spare Parts!

Steering Limiter for useing with Bellcrank Steering (BSSX) AT18 has two modes of steering angle limiting 1) for carpet, 2) for asphalt. These two limits are based on data and setups from our team drivers. Designed for AM79A only. Check the pictures if you want to know if you have AM79 or AM79A.

Spur Axle

Awesomatix A700-AT20-5 - Spur Axle for SD2 - Spur Damper

Spur axle M

Awesomatix A700-AT21S/4 - Pivot Ball Short x4 Steel Version of AT21S. Same height as AT21S. Features a hole on top to fit a 2.0mm allen wrench.

GD Case1

GD Case2

Genuine Awesomatix spare parts!

Genuine Awesomatix spare parts!

AT248 reduces the local load on the area of the front bumper center mounting screw on the lower deck. This reduces the chances of a lower deck damage at frontal impacts. Recommended for carbon lower deck in A800R car. Slight modification of the plastic bumper P14-R-1 is needed. For installation cut the center pin on P14-1-R and increase the hole till ID 5mm. Explanation...

AT25-2 is set of 2x 39mm length Turnbuckles. This optional set can be used as replacement for AT14 parts at the rear "Toe-In Turnbuckles". The thread will go more deep inside of P13-4 Ball Cups and secure the "Toe-In" stay more consistent at impacts. Contains 2pcs of AT25-2

The standard AT25 (which is 6mm shorter than this one) is near to the limit when using AM14LS with bellcrank steering and longer suspension arms (+0.5 and especially +1.5). AT25-44 will solve this issue. Set of four pieces.

Battery Post x2 Short version for ULCG batteries with 18.5mm battery height.

FFG Alloy Rod

Awesomatix A700-AT40-1 - Damper Cup

Spare part for ADC.

Damper vane for SPR02H3

Awesomatix A700-AT42-1 - Damper Case

A800 Alu Spur Nut AT55M is a more narrow version of AT55. Spezial designed for the Middle Motor conversion. Can be also used in all A800 and A800X Cars as option

A800 Alu Belt Tensioner

Take care: It's not easy to replace. Think of replacing AT120 als complete unit.

A800 Pulley Washer

Replacement for the ABS set.

Spare part for LS1 Has been shown as AT73 at the beginning. This was a mistake. Correct number is AT71.

Spare Parts for LS2

Sparepart for AT74

AT78 should be used with OR152 O-Ring. Only compatible to D2.2 dampers. Will replace the P45L sponge.

Spare Part for DL-A

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 6x10x3 x2

Genuine Awesomatix part!

Genuine Awesomatix part! This part is called B168ZZ in the manual.

2.4mm Ball x 17

4x1.5mm ball bearings x 8

Awesomatix A700-B63SS - MR63ZZ Bearing 3x6mm (2 pcs)

Bearing for LS2 - 7x2.5x3mm - (2pcs) Spare Parts for LS2 Is shown in the manual as B73RS

Bearing 4x7x2,5 x 2

High quality Ball Bearings with Si3N4 ceramic balls.The optimum to reduce the friction of your A800 drivetrain! Especially usefull for any stock class competition where the lowest friction of the drivetrain will result in higher topspeed and more consisten power for the runtime. Black Rubber seal on one side. Metal seal on the other side.

Bearing 4x8x3 x 2 Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.

Bearing 5x8x2.0 x 2

Awesomatix A700-B85RS - MR85RS Bearing 5x8mm (2 pcs) Please note: Even if the name is "RS", which means "rubber sealed" they will be delivered with a rubber sealing or just a metal sealing. Both is possible.