UPSIDE MEASURE PLATE FOR 1/10 TOURING CARS

COMPLETE SET OF SET-UP TOOLS + CARRYING BAG - FOR 1/10 TOURING CARS The set contains: 107702 - CHASSIS DROOP GAUGE SUPPORT BLOCKS (10 MM) FOR 1/10 (2) 107714 - ULTRA-FINE CHASSIS DROOP GAUGE 4.0-6.6MM 107716 - ULTRA-FINE CHASSIS RIDE HEIGHT GAUGE 107880 - CHASSIS BALANCING SIMPLE TOOL (2 PCS.) 109301 - UNIVERSAL EXCLUSIVE SET-UP SYSTEM FOR 1/10 TOURING CARS 109360 - ALU NUT...

ALU NUT FOR 1/10 TOURING SET-UP SYSTEM (4)

ALU SET-UP WHEEL FOR 1/10 RUBBER TIRES (4)

Alu Setup System - for measuring camber, caster and toe. There are different versions available: 108001 - 1:8 Onroad Suitable for cars like XRAY RX8. Does not fit for 1:8 GT (like XRAY GTX8). 108801 - 1:8 Offroad Sutiable for cars like XRAY XB8. XT8 will need a different toe gauge cause of the wider car. 108901 - 1:10 Offroad Suitable for cars like XRAY XB2, XT2, XB4, XT4 or...

Alu Set Up Wheels 1/10 & 1/12 Adapter

COMPLETE SET OF SET-UP TOOLS + CARRYING BAG - FOR 1/10 & 1/12 PAN CARS The set contains: 107713 - ULTRA-FINE CHASSIS RIDE HEIGHT GAUGE 2-15mm 107715 - RIDE HEIGHT GAUGE BEVELED 1-15mm 107718 - RIDE HEIGHT GAUGE 2.6-5.6mm 107880 - CHASSIS BALANCING SIMPLE TOOL (2 PCS.) 109401 - UNIVERSAL EXCLUSIVE SET-UP SYSTEM FOR 1/10 & 1/12 PAN CARS 107904 - QUICK-TWEAK STATION 199221 -...

ALU NUT M3 FOR 1/10 & 1/12 PAN CAR SET-UP SYSTEM (2)

Setup wheels are always used when you want to eliminate the tolerance that exists in practice with a rim or a tire. Especially with 1:12, the tire is a potent factor that can distort the measured values. A foam rubber tire wears unevenly - a measurement with used conical tires is therefore not 100% accurate. In order to enable exact and precise placement on a tweak board,...

Alu Setup System - for measuring camber, caster and toe. There are different versions available: 108001 - 1:8 Onroad Suitable for cars like XRAY RX8. Does not fit for 1:8 GT (like XRAY GTX8). 108801 - 1:8 Offroad Sutiable for cars like XRAY XB8. XT8 will need a different toe gauge cause of the wider car. 108901 - 1:10 Offroad Suitable for cars like XRAY XB2, XT2, XB4, XT4 or...

COMPLETE SET OF SET-UP TOOLS + CARRYING BAG - FOR 1/10 TOURING CARS The set contains: 107713 - ULTRA-FINE CHASSIS RIDE HEIGHT GAUGE 2-15mm 107715 - RIDE HEIGHT GAUGE BEVELED 1-15mm 107719 - Downstop Gauge 1.9-6.5mm 107880 - CHASSIS BALANCING SIMPLE TOOL (2 PCS.) 109501 - UNIVERSAL EXCLUSIVE SET-UP SYSTEM FOR 1/10 FORMULA CARS 107904 - QUICK-TWEAK STATION 199221 - SET-UP BAG...

Alu Setup System - for measuring camber, caster and toe. There are different versions available: 108001 - 1:8 Onroad Suitable for cars like XRAY RX8. Does not fit for 1:8 GT (like XRAY GTX8). 108801 - 1:8 Offroad Sutiable for cars like XRAY XB8. XT8 will need a different toe gauge cause of the wider car. 108901 - 1:10 Offroad Suitable for cars like XRAY XB2, XT2, XB4, XT4 or...

UPSIDE MEASURE PLATE FOR 1/8 GT CARS

COMPLETE SET OF SET-UP TOOLS + CARRYING BAG - FOR 1/8 GT The set contains: 107702 - SUPPORT BLOCKS 10mm (2) 107713 - ULTRA-FINE CHASSIS RIDE HEIGHT GAUGE 2-15mm 107718 - RIDE HEIGHT GAUGE 17-30mm 109601 - UNIVERSAL EXCLUSIVE SET-UP SYSTEM FOR 1/8 GT 199241 - SET-UP BAG FOR 1/8 CARS - EXCLUSIVE EDITION

CNC-machined premium-quality aluminum set-up wheels for 1/8 GT cars allow for perfectly precise and repeatable set-up adjustment and tweak correction. Eliminates set-up errors inherent in using standard on-road tires. Precision-machined to exacting tolerances, each alu set-up wheel in a set is perfectly matched. Suspension set-up, ride height setting and checking tweak using...

Professional, ultra-compact work tray for set-up system and tools. CNC-machined from 1-piece aircraft aluminum. Extremely durable and wear resistant due to hard black coating. The parts tray features various compartments for set-up system parts, shock stands, set-up wheels, balancing tools, and other accessories. Perfect for all classes and scales. Rear part of the tray...

HUDY Bulkhead Alignment Tool for touring car bulkheads with spacing of 17mm allows for easy, comfortable and fast alignment of bulkheads. The alignment tool is placed between the left and right bulkheads with the included steel shafts. With the block and pins in place the driver can loosen and retighten both the lower bulkhead mounting screws and also the upper clamps and...

O-Ring for 1/12 + 1/10 Pan Car Setup Wheels (2 pcs)

Off-Road Setup book language: English

Set-Up Book language: English

With the advanced suspension geometry of Awesomatix cars you can set caster, camber and toe by adjusting the turnbuckles. With the help of a 1/10 scale setup system it's possible to visualize these values. To correctly set the caster of your Awesomatix TC you need our MXLR Awesomatix Caster Tools. Just release the outer round head screw on top of the wheel hub (AM06), and...

We noted there are a few 1/10 TC setup systems out there which have a wrong caster scale engraved. You can see a comparison picture in the gallery below to identify if yours is correct or wrong. If the scale is too narrow, its a one of the not correct versions out there, and your caster setting isn't actually the number it shows! With our MXLR Caster correction stickers you...

We noted there are a few 1/10 TC setup systems out there which have a wrong caster scale engraved. You can see a comparison picture in the gallery below to identify if yours is correct or wrong. If the scale is too narrow, its a one of the not correct versions out there, and your caster setting isn't actually the number it shows! With our MXLR Caster correction stickers you...

We noted there are a few 1/10 TC setup systems out there which have a wrong caster scale engraved. You can see a comparison picture in the gallery below to identify if yours is correct or wrong. If the scale is too narrow, its a one of the not correct versions out there, and your caster setting isn't actually the number it shows! With our MXLR Caster correction stickers you...

For the use with 1:10 touring cars.

To be used with 1:10 touring cars.

For the use with 1:10 touring cars.

Simple yet effective tool for marking wheel wells for easy cutting out, besides wheel wells you can also mark the height of how far it is off the ground. Which is sometimes required sometimes racing on carpet tracks and to avoid your body scraping on the floor and affecting performance! Besides for touring cars, there is an marked section in the center for marking mini...

Accurately check if your 1/10 touring car has any form of tweak with this set of bearing supported weighted setup wheels! Place your car on a flat surface and have the weights spun on their side. Slowly lift your chassis and if a side rotates first, means that corresponding side is tweaked. Adjust your spring preload accordingly.

Set-up System Stand - for 1/10th On-Road HUDY and Arrowmax

Camber Gauge - +5° bis -15° - composite - black

Ride Height Gauge - 3mm bis 15mm - Aluminium - Gunmetal Replacement for B0546

Level Board - easy installation - easy level adjust from the top - flat head screw preventing damage the board - full set stainless steel screw - 10mm height - 15mm aluminium leveler - up to 13mm board

Level Board - easy installation - easy level adjust from the top - flat head screw preventing damage the board - full set stainless steel screw - 10mm height - 15mm aluminium leveler - up to 11mm board

Ultra Shock Stand TC (blue)

Ultra Shock Stand TC (light blue)

Ultra Shock Stand TC (orange)

Ultra Shock Stand TC (red)

In order to optimally coordinate a car that can be driven in a balanced way in all situations, a computer-controlled weighing system is essential. SKYRC's Bluetooth Corner Weight System can help achieve just that. The system measures the weight on each individual axis on the model. Thus, it pretty much reflects the existing weight distribution of the racing car on each wheel...

Suitable for 1/10 touring cars (or other cars up to 80mm tire diameter). Needs to by used with an Android / iOS app which can be downloaded for free.

Suitable for 1/8 cars (or other cars up to 100mm tire diameter). Needs to by used with an Android / iOS app which can be downloaded for free.

SkyRC 600069-06 - Aluminium Setup Wheels (4) - BLACK

Aluminium Setup Wheels (4) - BLUE

To measure the chassis droop correctly and precise you will need a chassis droop gauge. With this tool you can measure the positive and negative chassis droop as well. The chassis droop is one of the most important setup parameter as this take effect on the chassis rolling as well as on the weight balance during acceleration and braking and in corners. Scope of Supply: 2x...

Aluminium Chassis Droop Gauge - 4.0 - 6.6mm - BLACK Technical Data: Measurement range: 4 - 6,6mm Step: 0,2mm

Aluminium Chassis Droop Gauge - -3.0 - 10.0mm - BLACK Technical Data: Measurement range: -3.0 - 10.0mm Step: 1mm

With this gauge you can measure the right height of your car, or let`s say you can measure the clearance between the chassis bottom and the ground. Similar than the chassis droop the right height take effect on the rolling of the chassis, the traction and the speed you can have through a corner. Technical Data: Measurement Range: 3,8 - 7mm Steps by: 0,2mm Scope of Supply: 1x...

Steel Cutting Tool for tire truer (e.g. HUDY) 21mm length - 2.1mm width. Does NOT fit for HUDY tire truers - they need a maxium of 1.5mm.

Set of 10pcs - 10mm outer diameter.

Suitable for a range from 19 to 30mm ride height.

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 19mm or 22mm gap between the bulkheads. For example: Yokomo BD7 XRAY T4 Team C TC10 Tamiya 418 Hot Bodies Pro 5 ARC ...and many more. Check your gap!

Eliminate tweak with the T-Work's Tweak Terminator Usage: 1. Clean bottom of main chassis and ensure no screws or parts protrude beyond the bottom surface of main chassis 2. Loosen upper chassis screws and place touring car on hard flat surface (e.g. glass) 3. Press Tweak Terminator down onto front and rear shock towers and tighten upper chassis screws NEW V2 - splitted into...

Eliminate tweak with the T-Work's Tweak Terminator Usage: 1. Clean bottom of main chassis and ensure no screws or parts protrude beyond the bottom surface of main chassis 2. Loosen upper chassis screws and place touring car on hard flat surface (e.g. glass) 3. Press Tweak Terminator down onto front and rear shock towers and tighten upper chassis screws NEW V2 - splitted into...

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 20mm gap between the bulkheads. For example: Mugen MTC-1 Infinity IF14 ...and many more. Check your gap!

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 18mm or 19mm gap between the bulkheads.

Place it between your bulkheads to make sure to have always straight bulks without any tweak. Suitable for cars with 16mm or 17mm gap between the bulkheads.

You want to have your car well balanced? Just do it... :-)

Suitable for a range from 3 to 7.5mm ride height.

Suitable for a range from 3 to 15mm ride height.